User Manual
Table Of Contents
- 1 General Information 概述 產品資訊
- 2 System Setup 系统安装 系統安裝
- 3 Operation 操作
- A Exploded Diagram& Parts List 分解图&部件列表 分解圖&零件表
v IPC-220/IPC-240 User Manual/ 用户手册
30. Observe local occupational health and safety requirements and guidelines for
manual materials handling.
31. Do not attempt to move a equipment by yourself; at least two people are needed
to move a equipment.
32. Use only the power cords and power supply units provided with your equipment.
33. Operation of the device without regulatory approval is illegal.
34. CAUTION: Disposal of a battery (or battery pack) into fire or a hot oven, or
mechanically crushing or cutting of a battery (or battery pack) can result in an
explosion. Leaving a battery (or battery pack) in an extremely high temperature
environment can also result in an explosion. A battery (or battery pack) sub-
jected to extremely low air pressure may also result in an explosion. Discard
used batteries according to the manufacturer’s instructions.
35. CAUTION: To disconnect power, remove all power cords.
36. CAUTION: Follow the user manual to operate the equipment.
37. CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equip-
ment.
Contact information:
Advantech Co., Ltd.
Website: www.advantech.com.tw
Address: No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan
114, R.O.C.
TEL: +886-2-27927818
1. 请仔细阅读此安全操作说明。
2. 请妥善保存此用户手册供日后参考。
3. 用湿抹布清洗设备前,请确认拔除电源线。请勿使用液体或去污喷雾剂清洗设
备。
4. 对于使用电源线的设备,设备周围必须有容易连接的电源插座。
5. 请不要在潮湿环境中使用设备。
6. 请在安装前确保设备放置在可靠的平面上,意外摔落可能会导致设备损坏。
7. 请不要将设备放置在超出建议温度范围的环境,即不要低于 0° C(32°F) 或高
于 40°C (122°F), 否则可能会造成设备损坏。
8. 设备机壳的开孔适用于空气对流,为了防止设备过热。请勿覆盖开孔。
9. 当您连接设备到电源插座前,请确认电源插座的电压符合要求和接地连接。请确
认电源线连接到有接地设备的插座。
10. 请将电源线布置在人们不易绊倒的位置,请勿在电源在线覆盖任何杂物。
11. 请注意设备上所有的警告和注意标语。
12. 如果长时间不使用设备,请拔除与电源插座的链接,避免设备被超标的电压波动
损坏。
13. 请不要让任何液体流人通风口,以免引起火灾或短路。
14. 请不要自行打开设备。为了确保您的安全,设备的维修只能由经过培训的维修人
员进行。 请不要自行打开设备。为了确保您的安全,请由经过认证的工程师来
打开设备。
15. 如遇下列情况,请由专业人员来维修:
电源线或者插头损坏;
设备内部有液体流入;
CLASS I LASER PRODUCT
KLASS I LASER PRODUKT