User manual
Table Of Contents
- ARK-3399
- 1 General Introduction
- 2 H/W installation
- 2.1 Introduction
- 2.2 Jumpers
- 2.3 Connectors
- Figure 2.2 ARK-3389 IO connectors drawing
- 2.3.1 ARK-3399 external I/O connectors
- 2.3.1.1 COM Connectors
- 2.3.1.2 Ethernet Connector (LAN)
- 2.3.1.3 PS2 Keyboard/Mouse Connector
- 2.3.1.4 VGA Connector
- 2.3.1.5 USB Connector
- 2.3.1.6 Power Input Connector
- 2.3.1.7 Power ON/OFF Button
- 2.3.1.8 LED Indicators
- 2.3.1.9 Audio Connector
- 2.3.1.10 DIO Connector
- 2.3.1.11 LVDS Connector
- 2.3.1.12 LCD Backlight On/Off control Connector
- 2.4 Installation
- 3 BIOS Operation
- 3.1 BIOS Introduction
- 3.2 BIOS Setup
- 3.2.1 Main Menu
- 3.2.2 Standard CMOS Features
- 3.2.3 Advanced BIOS Features
- 3.2.4 Advanced Chipset Features
- 3.2.5 Integrated Peripherals
- 3.2.6 Power Management Setup
- 3.2.7 PnP/PCI Configurations
- 3.2.8 PC Health Status
- 3.2.9 Frequency/Voltage Control
- 3.2.10 Load Optimized Defaults
- 3.2.11 Set Password
- 3.2.12 Save & Exit Setup
- 3.2.13 Quit Without Saving
- 4 Full Disassembly Procedure
- 4.1 Introduction
- Figure 4.1 Unscrew the bottom screws
- Figure 4.2 Unscrew the frame screws and remove the frame
- Figure 4.3 Unscrew the panel screws
- Figure 4.4 Unscrew the hex-bolts on the panel
- Figure 4.5 Unscrew the ground wire of LVDS cable and disconnect all the cables and boards
- Figure 4.6 Unscrew the boards’ screws and hex-bolts for disassembly
- Figure 4.7 Unscrew the power module screws on the bottom to disassemble the power module
- 4.1 Introduction
ARK-3399 User Manual 26
USB-ZIP Select boot device priority by USB-ZIP.
USB-CDROM Select boot device priority by USB-CDROM.
USB-HDD Select boot device priority by USB-HDD.
LAN Select boot device priority by LAN.
Disabled Disable this boot function.
Boot Other Device [Enabled]
When enabled, the BIOS will automatic to select next boot device.
Boot Up NumLock Status [On]
This item enables users to activate the Number Lock function upon system boot.
Typematic Rate Setting
This item enables users to set the two typematic controls items.
This field controls the speed at
- Typematic Rate (Chars/Sec)
This item controls the speed at system registers repeated keystrokes.
Eight settings are 6, 8, 10, 12, 15, 20, 24 and 30.
-Typematic Delay (Msec)
This item sets the time interval for displaying the first and second characters. Four
delay rate options are 250, 500, 750 and 1000.
Security Option [Setup]
System System can not boot and can not access to Setup page if the correct
password is not entered at the prompt.
Setup System will boot, but access to Setup if the correct password is not
entered at the prompt. (Default value)
ACPI Mode [Enable]
This item sets the operating in Advanced Configuration and Power Interface in Win-
dows 2000-based computer for Power saving Function.
MPS Version Control for OS [1.4]
This item sets the operating system multiprocessor support version.
OS Select For DRAM > 64M [Non-OS2]
Select OS2 only if system is running OS/2 operation system with greater than 64MB
of RAM on the system.