User Manual IPC-603MB Ultra Compact 2U Rackmount IPC Chassis with Front I/O Interfaces
Copyright The documentation and the software included with this product are copyrighted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Read these safety instructions carefully. Keep this user manual for later reference. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. For pluggable equipment, the power outlet shall be installed near the equipment and shall be easily accessible. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation.
18. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. 19. CAUTION: Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. 20.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Initial Inspection When you open the carton, please make sure that the following materials have been shipped: ! Chassis ! User Manual ! Warranty Card ! Accessory box with a package of screws (for fastening the disk drives, motherboard, ears and handles, etc.), a plastic post, and a pair of ears and handles. If any of these items are missing or damaged, contact your distributor or sales representative immediately. We have carefully inspected the IPC-603 mechanically and electrically before shipment.
Contents Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 Environmental Specifications .................................................................... 2 Table 1.1: Environmental Specifications ..................................... 2 Power Supply Options......
IPC-603MB User Manual viii
Chapter 1 1 General Information This chapter provides general information about the IPC-603MB.
1.1 Introduction IPC-603MB is an ultra compact 2U-high rackmount industrial computer chassis designed for space-conscious applications. With only 310 mm depth, IPC-603MB can accept any of Advantech ATX/mATX motherboards, and up to three half-sized add-in cards with the supported riser card. 1.
Chapter 1 1.5 Dimension Diagram General Information Figure 1.
IPC-603MB User Manual 4
Chapter 2 2 System Setup This chapter introduces the installation process.
The following procedures are provided to assist you in installing a motherboard, drives, and add-on cards into the chassis. Refer to Appendix A, Exploded Diagram, for all the detailed parts. 2.1 Removing the Top Cover To remove the top cover of IPC-603MB, please refer to Figure 2.1. Figure 2.
IPC-603MB accepts both ATX and microATX motherboards. To install a motherboard, please proceed as follows: Note! 3. Remove the three screws from the L-form riser card holder in the chassis. From inside of the chassis, attach the motherboard I/O shield to the front plate of the chassis. Check all devices, such as CPU, CPU cooler, and RAMs and make sure they have been installed on the motherboard correctly. Carefully place the motherboard in the chassis and fix it with screws.
2.3 Installing a Riser Card and Add-on Cards The IPC-603MB can accept up to three half-sized PCI add-on cards via the riser card. To install a riser card and add-on card, face to the rear side of the chassis and proceed as follows: 1. Insert the riser card to the 6th slot of the ATX motherboard or the 3rd slot of the microATX motherboard. 2. Remove the I/O bracket attached to the rear plate of the chassis. 3.
Chapter 2 HDD Slim CD-ROM 1. 2. 3. 4. 5. 6. Open the top cover of the chassis. Remove the four screws that mount the drive bay bracket kit in the chassis. Remove the front cover of the slim-type ODD from the bracket kit. Refer to Figure 2.4 and mount a slim-type ODD and a 3.5" HDD with screws. Return the drive bay bracket kit into the chassis and fix it with screws.
IPC-603MB User Manual 10
Chapter 3 3 Operation This chapter introduce the system operating information.
3.1 The Front Panel 3.1.1 Switch and button There is a power switch and a system reset button on the front panel. Press the System Reset button to reinitialize the system. Press the Power On-Off Switch to turn the system power on or off. 3.1.2 LED indicators Two LEDs indicate the system status. Refer to Table 3.1 for the LED summary. Table 3.
To change the filters, refer to Figure 3.2 and proceed as follows: 1. Open the top cover of the chassis. 2. Pull out the filters and replace it with a new one. filter filter Chapter 3 3.3 Replacing the filters filter Operation Figure 3.2 Replacing the filters 3.4 Replacing the power supply IPC-603MB supports a single 1U-high power supply. To replace the power supply, refer to Figure 3.
4. 5. 6. 7. 8. 9. Refer to Figure 3.3 to remove the drive bay. Remove the six screws which mount the power supply to the chassis, then lift the power supply. Place a new power supply into the chassis and fasten it with the screws. Return the drive bay to the chassis. Plug the ATX power connector and +12V power connector into the motherboard, and the peripheral power connector(s) into the proper disk(s). Replace the top cover and plug in the power cord.
Appendix A A Exploded Diagram
A.1 Exploded Diagram Figure A.
Appendix B B Motherboard & Riser Card Options
B.1 Motherboard Options The IPC-603MB supports a variety of Advantech ATX/MicroATX motherboards described below. Contact a local sales representative for more detailed information. Table B.
The riser card is specially designed to support Advantech AIMB series of motherboards. Table B.
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
