User manual

ManualsBrandsAdvantech ManualsComputer equipmentAIMB-203

i AIMB-203 User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ............................................................................................... 2

1.2 Features .................................................................................................... 2

1.3 Specifications ............................................................................................ 2

1.3.1 System .......................................................................................... 2

1.3.2 Memory ......................................................................................... 2

1.3.3 Input/Output .................................................................................. 2

1.3.4 Graphics........................................................................................ 3

1.3.5 Ethernet LAN ................................................................................ 3

1.3.6 Industrial features ......................................................................... 3

1.3.7 Mechanical and environmental specifications............................... 3

1.4 Jumpers and Connectors .......................................................................... 4

Table 1.1: Connector and Header List......................................... 4

Table 1.2: Jumper List ................................................................. 5

1.5 Board layout: Jumper and Connector Locations ....................................... 6

Figure 1.1 Jumper and Connector Location ................................ 6

1.6 AIMB-203 Board Diagram ......................................................................... 7

Figure 1.2 AIMB-203 Board Diagram .......................................... 7

1.7 Safety Precautions .................................................................................... 7

1.8 Jumper Settings ........................................................................................ 8

1.8.1 How to Set Jumpers...................................................................... 8

1.8.2 CMOS Clear (JCMOS1)................................................................ 8

Table 1.3: CMOS1....................................................................... 8

1.8.3 Case open selection pin header (JCASEOP_SW1) ..................... 8

Table 1.4: Case open selection pin header (JCASEOP_SW1) ... 8

1.8.4 COM1_RI# Pin RI#/5V/12V selection (JSETCOM1_V1) .............. 9

Table 1.5: COM1_RI# Pin RI#/5V/12V selection

(JSETCOM1_V1)........................................................ 9

1.8.5 COM2_RI# Pin RI#/5V/12V selection (JSETCOM2_V1) .............. 9

Table 1.6: COM2_RI# Pin RI#/5V/12V selection

(JSETCOM2_V1)........................................................ 9

1.8.6 COM5 RS232,RS422,RS485 selection pin header (JSETCOM5)..

Table 1.7: COM5 RS232,RS422,RS485 selection pin header

(JSETCOM5) ............................................................ 10

1.8.7 ATX/AT Mode Selection (PSON1) .............................................. 11

Table 1.8: ATX/AT Mode Selection (PSON1)............................ 11

1.8.8 LVDS Panel Voltage Selection (JLVDS1)................................... 11

Table 1.9: LVDS Panel Voltage Selection (JLVDS1) ................ 11

1.8.9 Watchdog timer output and OBS beep (JWDT1+JOBS1) .......... 11

Table 1.10:Watchdog timer output and OBS beep

(JWDT1+JOBS1)...................................................... 11

1.8.10 Power switch/HDD LED/SMBus/Speaker pin header (JFP1) ..... 12

Table 1.11:Watchdog timer output and OBS beep

(JWDT1+JOBS1)...................................................... 12

1.9 System Memory ...................................................................................... 12

1.10 Memory Installation Procedures.............................................................. 12

1.11 Cache Memory........................................................................................ 13

1.12 Processor Installation.............................................................................. 13

Chapter 2 Connecting Peripherals ....................15

2.1 Introduction ............................................................................................. 16

2.2 USB Ports (LAN1_USB12/LAN2_USB34/USB56/USB78) ..................... 16