User's Manual
Table Of Contents
- ADAM-2000 Series
- 1 Understanding Your System
- 1.1 Introduction
- Figure 1.1 ADAM-2000 Series System Architecture
- Figure 1.2 ADAM-2000 Series Operating Distance
- 1.1.1 IEEE 802.15.4 Wireless Standard
- 1.1.2 Wireless Sensor Network
- 1.1.3 Low-power Consumption and Battery-Powered Design
- 1.1.4 Sensor Embedded Design
- 1.1.5 Wireless Signal Indicator
- 1.1.6 Industrial Standard Modbus Protocol
- 1.1.7 SCADA Software Support
- 1.1.8 Advantech Software Alignment
- 1.2 Specifications
- 1.3 Dimensions
- 1.4 Mounting
- 1.5 Wiring & Connections
- 1.1 Introduction
- 2 Selecting Your Hardware
- 3 Module Introduction
- 4 Installation Guide
- 5 Software Configuration Guide
- 5.1 System Software Configuration Utility
- 5.2 Installing AdamApax .NET Utility Software
- 5.3 AdamApax .NET Utility Operation
- Figure 5.1 AdamApax .NET Utility Operation Window
- Figure 5.2 AdamApax .NET Utility Toolbar
- 5.3.1 USB Driver Installation
- 5.3.2 Search and Configure the ADAM-2000 Series
- Figure 5.3 ADAM-2000 Series AdamApax .NET Utility Support
- Figure 5.4 Search the USB interface ADAM-2000 devices on the host PC for the virtual COM port.
- Figure 5.5 Search the COM port for the ADAM-2000 devices.
- Figure 5.6 Searching the network dialog
- Figure 5.7 Searching the ADAM-2000 coordinators.
- Figure 5.8 ADAM-2000 devices lists on the Tree View and Information page.
- Figure 5.9 The overview of ADAM-2000 end devices.
- Figure 5.10 The overview of ADAM-2000 routers
- 5.3.2.1 Gateway - ADAM-2520Z
- 5.3.2.2 Router - ADAM-2510Z
- 5.3.2.3 End Device - ADAM-2017PZ, ADAM-2031Z, ADAM-2051Z, ADAM-2051PZ
- 5.3.3 Network Topology of ADAM-2000 Series
- 5.3.4 Module Locate Function of ADAM-2000 Series (Except ADAM- 2520Z)
- 5.3.5 Group Configuration
- A ADAM-2000 Series Functions
- B Troubleshooting
- 1 Understanding Your System
ADAM-2000 Series User Manual 72
A.2.4 ADAM-2031Z
Wireless Sensor Network Temperature and Humidity Sensors Node
03 Read Holding Registers
Table A.5: ADAM-2031Z Mapping Table
Address 4X Description Attribute Value
40001 Temperature Input Read 0x0000 ~ 0xFFFF*
40002 Humidity Input Read 0x0000 ~ 0xFFFF**
40211 Module Name 1 Read 0x2031
40212 Module Name 2 Read 0x5A00 (ASCII Code of 'Z')
40213
Wireless Module
Firmware Version 1
Read
Version Number
(ex: 0xA210 means version A2.10)
40214
Wireless Module
Firmware Version 2
Read
Build Version Number
(ex: 0x0003 means version B03)
40301 Module Status Read
Bit 0: 0; Initial Mode
Bit 0: 1; Normal Mode
Bit 1: 0; No External Power Input
Bit 1: 1; External Power Input
40302 LQI Read
0x0000~0x00FF;
0x0000: No Signal
0x00FF: Excellent
40303 Battery Level Read
0x0000; Low
0x4000; Poor
0x8000; Normal
0xC000; Good
0xFFFF; Excellent
40304
Device Inactive Period
(Upper word)
Read
0 ~ 259200 seconds;
Maximum 3 days record
(Total 51840 steps; 5 seconds per step)
40305
Device Inactive Period
(Lower word)
40306 Link Status Read
Bit 0: Connected
Bit 1: Link Failure
Bit 2: Disconnected
Bit 3: Connecting
40307
Data Cycle Time
(Upper)
Read
0x00000001~0x00015180
(1 ~ 864000 seconds)
40308
Data Cycle Time
(Lower)
40309 LQI Percentage Read 0x0000~0x0064 (0~100%)
40310 Device Short Address Read 0x0000~0xFFFF
40311 Parent Address Read 0x0000~0xFFFF
Note!
* The temperature T is calculated by inserting temperature signal output
S
T
into the following formula (result is in
o
C).
T 46.85–
175.72x
S
T
2
16
-------
+=