Scope This manual is intended for use by service technicians familiar with similar types of equipment. It contains service information required for the equipment described and is current as of the printing date.
Product Safety and RF Exposure for Portable Two-Way Radios Compliance with RF Energy Exposure Standards NOTICE: This radio is intended for use in occupational/controlled applications where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use.
* If you are not using a body-worn accessory and are not using the radio held in front of the face, ensure the radio is kept a minimum of 1.3 cm from the body when transmitting. Keeping the radio at a proper distance is important since RF exposure decreases with increasing distance from the antenna. FCC license Information Your Advanced Wireless Communications radio operates on communications frequencies which are subject to FCC (Federal Communications Commission) Rules & Regulations.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Brief Introduction 1. 2. 3. 4. 5. 6. 7. 8. Antenna Used to receive or transmit signals. LCD Displays operation status of the radio. LED indicator In transmit mode, the red LED will turn on. In receive mode, the green LED will turn on. A flashing red LED indicates that the battery is low. POWER/VOL Knob Rotate the volume control clockwise to turn the unit on, fully counter clockwise to turn the unit off. Increase or decrease volume by adjusting the volume control accordingly.
9. MONI button In receive mode, press the MONI key to monitor activity on your selected channel. 10. Microphone Input audio. 11. Earpiece Jack/ PC programming port Used to connect external earphone/microphone accessories or used to connect with programming cable. 12. Speaker Output audio. 13. DC jack Used for factory adjustment only. 14. Battery latch Used to fasten and remove the battery. 15. Belt clip Used to clip radio on your belt. 16.
LCD Display 1. 2. 3. 4. Appears when the transmit power of the current channel is set for low power. Appears when the dealer disables the radio’s speaker. Appears when the keys are locked. Display the current channel number.
Dealer Operation Description Keys combination Key Function MONI+SCAN Key Lock/unlock (dealer can program it ON/OFF) MONI+UP Change CTCSS/CDCSS number (dealer can program it ON/OFF) MONI+DOWN Adjust squelch level 0-9(dealer can program it ON/OFF) PTT+MONI High/low power (dealer can program it ON/OFF) Dealer Mode Turn on the radio while pressing [PTT] and [SCAN] simultaneously, in 3 seconds, the radio enters Password Check (if password has been set) or Dealer Menu. 1.
(1) (2) (3) (4) (5) (6) (7) Password contains 6 digits (0-9). After correct password is checked, a new password can be entered and original one can be cancelled. Press [SCAN] to enter password-entering mode. Press [UP]/[DOWN] to enter digits (0-9). Press [SCAN] to delete entered password or cancel password. Delete entered password: LCD displays“------”. The first “-” blinks. Cancel password: LCD displays “CANCEL”. “CANCEL” blinks. Press [PTT] to confirm the entered.
Press [UP]/[DOWN] to select the channel which needs to be programmed. Press [MONI] to return to Power On Menu. 2. Press [PTT], LCD displays the receive frequency of current channel as follows: Press [SCAN] to toggle LCD display between frequency and blank, as follows: Frequency change operations: Press [UP] or [DOWN] to change frequency upwards or downwards. (In step of 5 KHz or 6.25KHz) Hold down [UP] or [DOWN] to continuously change frequency.
(3) CDCSS (4) Reverse CDCSS 4. Press [PTT], LCD displays transmit frequency of current channel as follows: The setting operations are same as those of receive frequency. 5. Press [PTT], LCD displays transmit CTCSS/CDCSS number: The setting operations are same as those of receive CTCSS/CDCSS. CTCSS/CDCSS CTCSS NO. Freq (Hz) NO. Freq (Hz) NO. Freq (Hz) 00 NO TONE 13 103.5 26 162.2 01 67.0 14 107.2 27 167.9 02 71.9 15 110.9 28 173.8 03 74.4 16 114.8 29 179.9 04 77.
CDCSS NO. CODE NO. CODE NO.
(2) dEL: delete the channel from scan list, and the channel (except priority channel) will not be scanned. 7. Press [PTT], LCD displays “HI”/“LO”. Press [UP]/[DOWN] to toggle RF power between high and low. LCD displays as follows: 8. Press [PTT], LCD displays “BSy On”/“BSyOFF”. Press [UP]/[DOWN] to toggle Busy Channel Lockout between ON and OFF. 9. Press [PTT] to save settings. Press [PTT] again to enter the next channel and continue the settings. When settings are completed, turn off power to exit.
1CH(C) Model Freq. (MHz) IF. (MHz) 2CH(L) 3CH(H) 4CH 5CH 6CH 7CH 8CH 9-99CH (MHz) Tx (MHz) Rx (MHz) Tx (MHz) Rx (MHz) Tx (MHz) Rx (MHz) (MHz) (MHz) (MHz) (MHz) (MHz) 1 150.000~173.995 +45.05 162.000 162.100 150.000 150.100 173.975 173.900 162.500 162.550 162.600 162.550 162.650 2 136.000~149.995 +45.05 143.000 143.100 136.000 136.100 149.975 149.900 143.500 143.550 143.600 143.550 143.650 3 146.000~173.995 +45.05 160.000 160.100 146.000 146.100 173.
Function set Select “FUNSEt” in Power On Menu. The radio enters function set mode. Setting Function Settings Display No. name (Defaults are ([UP]/ (PTT) underlined) [DOWN]) OFF 1 2 Monitor Scan OFF Specifications Monitor function is OFF Monitor Momentary 1 Hold down [MONI] to cut off signaling temporarily. Monitor Lock 2 Press [MONI] to cut off signaling. Switches each time [MONI] is pressed. SQ OFF Momentary 3 Hold down [MONI] to open squelch.
Setting Function Settings Display No. name (Defaults are ([UP]/ (PTT) underlined) [DOWN]) 9 Time Out 0 timer 1-10 (TOT) 6 10 Beep ON ON: Beep is on. OFF OFF OFF: Beep is off. ON ON ON Backlight is enabled. OFF OFF: backlight is disabled. Backlight OFF 12 Wideban- Wideband d/Narrow Narrowband -band Battery save OFF OFF: 10 minutes 30-300 (Step: 30s) 180 ON 11 13 Specifications 25 1250 ON ON OFF OFF 25 25.0KHz 1250: 12.
PC programming Connect a PC and a radio with a programming cable, and then program the radio by the PC. 1). Write data into the radio, green LED glows; read data from the radio, red LED glows. During programming, LCD displays as cloning, “c” blinking. When programming is complete, blink stops and LCD displays“-c-End”. 2). When PC tune mode begins, LCD displays “tune”. There are the following options in the tune mode: . Low battery alert level LCD displays “ tuneb”. .
LCD displays “SENS H” ([PTT]: R/T, SCAN, wide/narrow) (11). Center Frequency with CTCSS 250.3 check LCD displays “SENC 38” ([PTT]: R/T, SCAN, wide/narrow) Operations: Press [UP]/[DOWN] to select the next menu option. Press [PTT] to enter option settings: In [1]-[7] options, LCD displays blinking digits. Now press [UP]/[DOWN] to adjust, press [MONI] to exit. In [8]-[11] options, C/L/H blinks, indicating center frequency, low frequency or high frequency.