NEWPORT ULTRA AIR PURIFIER Real Spirit USA, Inc. 320 South Rock Blvd. Ste. 210 Reno, Nevada 89502 Tel:1-888-698-2080 Website: www.AdvancedPureAir.com Info@AdvancedPureAir.
NEWPORT ULTRA AIR PURIFIER PURE CONTROL
SAFETEY OPERATION Please exercise caution when using this air purifier or any other electrical device! This manual describes the safety precautions which should be observed in relation to your air purifier. Please review carefully BEFORE using this product. CAUTION RATED VOLTAGE DO NOT DISMANTLE The voltage rating for air purifiers sold in the USA, Japan and Canada is AC100-120V, 50/60Hz and in Europe is AC 230V, 50Hz. Using the wrong current may result in unit damage, electrical shock or fire.
DESCRIPTION OF THE APPLIANCE Control panel Handle Clean sign Air Inlet Air Inlet Back View Air Outlet Dust Sensor Handle Gas Sensor MAJOR COMPONENTS DC FAN TiO2 Filter Activiated Carbon/Formaldhyde Filter HEPA Filter Dust Collector Cell Pre-filter UV LED Front cover 3
PREPARATIONS BEFORE USE ACCESSORY LIST Please check all the accessories are available before operating Owner's Manual Owner's HEPA Filter Pre-filter Dust Collector Cell Manual Activated Carbon/Formaldhyde Filter TiO2 Filter USES OF FILTERS For initial use or filter replacement, please remove the plastic bag of filter. If the plastic bag is not removed, the unit may operate noisily. The purifying efficiency will decrease if the air purifier operates without filters.
PREPARATIONS BEFORE USE Operation Locate the unit on a solid surface. Be sure the air inlet/outlet is not blocked by other objects. (At least 30cm clearance on the sides) It is best to locate the unit where it will be out of any children's play area. Before plugging in the unit, please open the windows in the area where you will be using the unit. Ventilate the area for 2-3 hours if possible. Once the area has been ventilated, close the windows and plug in the unit.
INSTRUCTIONS FOR OPERATING Control Panel Instructions M F D L J C G A H I B K E A) On/Off Button By pressing button A once, you can switch the unit on, display screen will illuminate. The appliance will start to operate under AUTO mode. By pressing it twice, the unit is switched off. B) Fan Modes This unit has six different fan modes to choose from. Please choose a proper level of circulation according to the indoor air quality and room size.
INSTRUCTIONS FOR OPERATING C) Operation with photocatalyst(TiO2) Button C is used for switching the photocatalyst on and off (Symbol “UV” lights up). This appliance combines advanced photocatalyst technologies to reduce odors and chemical fumes from glues, solvents, and synthetic materials when air passes through the filter and is activated by the internal UV LED.
INSTRUCTIONS FOR OPERATING H) Child lock By pressing button E z zz and A for 3 seconds until buzzer beeps, Symbol “LOCK” appears on the display, child lock function is activated to prevent incorrect operation by children, all buttons are not unable to operate. Repeat above step to unlock. Lock/Unlock Buttons z zz + pressing for 3 seconds Lock/Unlock I) Sensor indicator Once the sensors detect gas or dust pass through the unit, Symbol “GAS” or “DUST” illuminates on the display.
CLEANING AND MAINTENANCE Cleaning the unit while it is plugged in may rusult in electric shock, electric spark and serious injury.Unplug the unit before cleaning or maintenance. Disassembling the Air Purifier After unplugging, disassemble the unit in sequence of 1 to 5 as shown below. (Put the unit back together in the reverse 5 to 1 sequence.
CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE 1 2 Clean the Front Cover ·Use a soft and wet cloth to clean, avoid scraping off the paint on the cover.
CLEANING AND MAINTENANCE Reset the "REPLACE FILTER” indicator Please refer to instructions on page 7 for resetting after replacement, otherwise the indicator will remain on screen. Cleaning the Dust Collector Cell Caution The dust collector cell may not require cleaning if “arcing” occurs. Arcing is a sharp snapping sound that occurs when large particles are collected in the dust collector cell or the appliance used in over damp rooms.
CLEANING AND MAINTENANCE 3 Clean the dust collector cell Use provided brush or toothbrush to clean. Please take care not to damage any wiring while cleaning the dust collector cell, if any wire is broken, the unit will lose part or all of its dust collecting capability. Any broken wire should be thrown away instead of being left inside the unit. Otherwise, a dangerous short-circuit or high-voltage sparks may occur. Please contact authorized service center for maintenance or replacement.
TROUBLESHOOTING Service problems that appear to be major can often be solved easily. You can be your own troubleshooter by reviewing this guide. All other servicing should be done by a local authorized service center. Problem Appliance does not turn ON Red “REPLACE FILTER” indicator has illuminated Red “CLEAN CELL” indicator has illuminated. Check Power cord Power button Front cover/Dust collector cell Filters Dust collector cell Solution Plug in power cord Press the power button.
TROUBLESHOOTING Problem Check Environment Solution Open the window to improve the ventilation Dust sensor gets dirty, please clean the dust senor, refer to “CLEAN SIGN” is instructions on page 10 always displaying polluted Possibly because the room is not really a closed environment Sensors and pollution keeps coming in from the outside. Or because there has been pollution created indoors (e.g. smoking/pet boxes etc.) the whole time.
SPECIFICATIONS Model Rated Voltage AP-HC300B AC110~120V/50-60Hz AC220~240V/50Hz Power 55W (Not include UV LED 10W) Activated Oxygen Output ≤0.05ppm Noise Level (dB) Silent 25/Low 35/Med 45/High 55dB/Turbo 60dB CADR Value 3 300M/H Dimensions (mm) 410×288×535mm Room Size 20-50m2 Net Weight 6.
