Annex No.
Stand Alone READER ST500 Users Interface Description AFG ASIA ENGINEERING CO.LTD. 65/12 M.10 T.Tonpao A.Sankumpang Chiangmai, Thailand 50130 Tel: +66 53 390 909 Fax: +66 53 390 910 Website : WWW.AAE.CO.
Contents : 8. 7.2.9 Help tab ............................................................................................... 13 FCC Statement ................................................................................................ 13 1. 2. 3. 4. 5. Pictures of UHF RFID Stand Alone Reader ST500........................................... 3 Pre-installation Precautions ............................................................................... 3 Abstract..........................................
• Set OWNER ID first and be sure the owner ID is NOT NULL.(see owner) 1. Pictures of UHF RFID Stand Alone Reader ST500 Front of Stand Alone Reader and components Antenna Package Contents 1. Stand Alone Reader ST500 (please see left pictures) DB9 connector 2. RS232 Communication cable 3. Switching Power supply DC power connector 4. Support CD Status LED 2.
• • Default setting: Owner ID / Physical Location data entry is ASCII, reading type is ISO and EM. In a pig farm, pigs get their food only if they didn’t eat yet. The information if he already eat or not is written in the tag of the animal allowing weight development control without networking several readers. 3. Abstract This document describes the user interface of the Stand Alone RFID reader ST500 for release 1.03 and further. 4.
.1 5.2 Writing data to Tag Some kinds of tags have an internal memory that can be written with user data. Please check the tag characteristics with the manufacturer. Data can be written into the Tags with PC application (see Support software) in 2 formats as; • ASCII : normal text • EPC : the EPC data must according to EPC Tag Data Standards. (Automotive Industry Action Group’s (AIAG) B-11 RFID Item Identification Standard.) 5.
Note : the reader timeout has no influence on the tag counting feature. 6.4 Operation mode You can set Operation mode with PC application (see Support software) in 2 modes as follow; • Read ID – Reader will read only Tag ID. • Read ID and Data – Reader will read Tag ID and also data in the same time. 6.5 - to download tag ID read by the unit - to write data into tags(ISO-EM tag, EPC tag) - to edit tag data - to configure operation for the unit Installation short descriptions : AAE Support CD.
Note : Support software are in AAE Support CD/PC Application. 7.1 Dot Net Frame work 2 (manual installation) This step is required if your PC does not already have .Net Framework v1 (only) already installed. If it does, setup software will skip to next section. To install Dot Net Framework 2.0 - double click the Dot Net Framework 2.0.exe icon (as left picture) - follow the instructions in dialogue boxes until installation is finish. (as lower picture) 7.
7.2.2 Start RFID Note Connection tab To start RFID Note - connect the Unit to PC with RS232 communication cable. (male side connect to unit and female side connect to pc) - switch “ON” the unit - double click on RFID Note icon (as a left picture) - then RFID Note starting window (see lower picture) and Connection tab window will appear. Ready connection Note : RS232 communication cable is in the reader package. (see package contents) 7.2.
You can perform Clear data grid, Delete rows, Grid customization, and Delete filter with 4 buttons.(left picture) 7.2.4 Download tab Download tab Download button Grouping area This tab is use for management the data from the unit. For example; - download tag ID read by unit. (you can download all the data or select from the specific address ) - download data from SD card. - make a online(real time) communication between unit an pc. - edit tag data, etc.
Note : You can cancel filter by click on Delete filter button on tools bar. (see left picture) 7.2.5 7.2.5.3 Owner and Reader ID You can set owner ID and Reader ID(unit ID) with this operation box. To set owner ID (the ID is depended on Control functions setting) - input value into Owner ID box then - click on Set owner button Reader Setting tab This tab is allow you to change configuration and set up the unit with firmware 5.00 and further.
- click on Program tag EPC To set Reader ID(unit ID) - input value into Reader ID box then - click on Set owner button to confirm You can save log file to keep the writing details for further use. - click on Save log file box - click on File path button and browse save location 7.2.6 Write EPC tag tab This tab is use for command unit to write data into EPC tag. 7.2.6.1 Set data length and start address First of all you need to set data length and start address to match EPC data format.
- input Access code - select operation you want to 7.2.7 Write ISO tag tab This tab is use for command unit to write data into ISO tag. 7.2.7.1 Set data length and start address First of all you need to set data length and start address to match EPC data format. Set data address and Data length need your confirmation because these operations will erase all data in the unit’s memory.
You can create new Note file, Save(AAN file), and Print your AID file with these 3 buttons . Note : AID file is a default data format for RFID Note. You can move to Download tab by clicking on Blue arrow button(save and back), and confirm changing any details in this tab with Green tick button.(save, update and back) You can add New Row or Delete Row with these buttons. You can browse file location with by clicking on File path button 7.2.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules.
