User Manual
Evolve Guest Controls LRM-20 Instructions
LRM-20
by Evolve Guest Controls
The LRM-20 can be set to respond to ALL ON and ALL OFF commands 4 different ways.
Refer to your controller for information on how to set the LRM-20 to operate in the manner you desire. Some controllers
may be only able to set certain settings of ALL ON/ALL OFF response.
The 4 different ways the LRM-20 can be setup to respond to ALL ON and ALL OFF commands are:
• LRM-20 will not respond to ALL ON or the ALL OFF command.
• LRM-20 will respond to ALL OFF command but will not respond to ALL ON command.
• LRM-20 will respond to ALL ON command but will not respond to ALL OFF command.
• LRM-20 will respond to ALL ON and the ALL OFF command (default).
Association
The LRM-20 supports the Association command.
The LRM-20 can be set to control other EvolveNet devices. . You can turn on and off, and even dim other EvolveNet devices
once they are “” in groups 2 and 3 with LRM-20.
A NOTE ABOUT DIMMERS IN A GROUP: If you combine EvolveNet enabled dimmers and other types of EvolveNet
devices in a group, place a EvolveNet enabled dimmer into the empty group first to ensure that the dimming operates cor-
rectly.
Each group is turned on, off or dimmed by tapping or holding the switch a differing amount of times.
Group 2
If you a EvolveNet device into Group 2, you can turn that device on and off by tapping the top or bottom of the switch twice.
You can brighten or dim devices by tapping the top or bottom of the switch once and then hold it down. The load attached
to the LRM-20 is not affected.
Group 3
If you a EvolveNet device into Group 3, you can turn that device on by tapping the top of the switch three times or off by
tapping the bottom of the switch three times. You can brighten devices by tapping the top of the switch twice or dim devices
by tapping the bottom of the switch twice and then hold it down. The load attached to the LRM-20 is not affected.
You can up to EvolveNet devices into each of these groups. For instructions on how to “” a EvolveNet device into one of
these groups, refer to your wireless controller instructions. (If you are using the EHC-100 controller, refer to the Setup Menu,
Association section).
A note about dimming, if you combine EvolveNet enabled dimmers and other types of EvolveNet devices in a group, place a
EvolveNet enabled dimmer into the empty group 1
st
to ensure that the dimming operates correctly.
Configuration
The LRM-20 supports the Configuration command.
The LRM-20 can be configured to operate differently than how it works when you first install it. Using the Configuration
command you can configure the following:
You can use a EHC-100 to send Configuration commands. (Refer to the Setup Menu, Configuration section)
The LRM-20 can send Dim commands to EvolveNet enabled dimmers. The Dim command has a start level embedded in
it. A dimmer receiving this command will start dimming from that start level if this bit is set to 0. If the bit is set to 1,
the dimmer will ignore the start level and instead start dimming from its current level. The LED on the LRM-20 will by
default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF
instead, set parameter 3 to a value of 1.
To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1.
The LRM-20 can control shade control devices via its group 2 if this configuration parameter is set to 1.The LRM-20
can control shade control devices via its group 3 if this configuration parameter is set to 1.The LRM-20 will flicker
its LED when it is transmitting to any of its groups. This flickering can be set to not flicker at all
(set to 0), to flicker the entire time it is transmitting (set to 1), or to flicker for only 1 second when it
begins transmitting (set to 2). By default, the LRM-20 is set to flicker for only 1 second.• • • Each
Configuration Parameter can be set to its default setting by setting the default bit in the Configuration Set command. See
your controller’s instructions on how to do this (and if it supports it).
All Configuration commands will be reset to their default state when the LRM-20 is excluded from the EvolveNet network by