ACR3901U-S User Manual Name Prepared by: Danny Deng Signature Date 2014-06-07 Reviewed by: Approved by: Subject to change without prior notice info@acs.com.hk www.acs.com.
Version History Date 2014-06-07 By Danny Deng Changes ● Initial released Version 1.00.00 ● Page 2 of 20 info@acs.com.hk Version 1.00 www.acs.com.
Table of Contents 1.0. USB Mode Loopback program .................................................................................. 4 2.0. Bluetooth Mode Loopback program......................................................................... 8 3.0. USB Mode Driver Installation .................................................................................. 12 4.0. Bluetooth Adaptor Driver Installation .................................................................... 16 Page 3 of 20 info@acs.
1.0. USB Mode Loopback program This section introduces ACR3901U-S Reader using in USB Mode Tools Requirement: a. ACR3901U-S reader b. ACOS3 Card c. USB Cable d. PC & USB Mode loopback program “ESD4.exe” Test Procedure: 1. Plug the ACR3901U-S reader into PC through USB cable 2. Turn the switch on reader to “USB Mode” (as the picture). *For the first time of use, user needs to install a reader driver on PC.
4. Step1 Press “Initialize” button to Search the smart card reader name Then you will find the “ACS ACR3901U ICC Reader 0” Page 5 of 20 info@acs.com.hk Version 1.00 www.acs.com.
5. Step2 6. Press “test” button Now you will see that the program is working The retry interval should be set to 15 Page 6 of 20 info@acs.com.hk Version 1.00 www.acs.com.
. Step3: After the testing, please press “Quit” button. 8. Unplug the reader cable and then switch the reader to “OFF”. Page 7 of 20 info@acs.com.hk Version 1.00 www.acs.com.
2.0. Bluetooth Mode Loopback program This section introduces ACR3901U-S Reader using in Bluetooth Mode Tools Requirement: a. ACR3901U-S reader b. ACOS3 Card c. USB Cable d. Bluetooth 4.0 USB Adaptor Dongle e. PC & Bluetooth Mode loopback program “ACR3901U-S1_BT.exe” Test Procedure: 1. Plug in the Bluetooth 4.0 Dongle into PC (*For the first time of use, please install the driver, please refer to section 4.0 – Bluetooth Adaptor Driver Installation) 2. Run “ACR3901U-S1_BT_Test.
5. Insert the “ACOS3” test card into the ACR3901U-S reader. 6. Plug the ACR3901U-S reader into PC through USB cable for providing power. 7. Turn the ACR3901U-S reader to “Bluetooth Mode” and check that the green LED on the reader will slowly flash. It means the reader is ready to be paired with. 8. Press the “Scan” button to scan the Bluetooth device. If a pairing ACR3901U-S reader is discovered, it will display the reader information as the picture below: Page 9 of 20 info@acs.com.hk Version 1.00 www.
9. Select the corresponding ACR3901U-S reader and then press “Connect” under Bluetooth device. If connection is successful, there will be the messages showing that the connection is successfully, as the picture below: 10. When the ACR3901U-S reader is successfully connected to the program, the blue LED and the green LED on the reader will flash slowly at the same time. Page 10 of 20 info@acs.com.hk Version 1.00 www.acs.com.
. Press “Start” button to start the test, now you will see the program is running for reading/writing card. The program running information will be shown on the message window. 12. After the testing, press “Stop” to stop the card test; and then press “Disconnect” to disconnect the ACR3901U-S reader and the program. There will be a popup window to show the device successfully disconnected, press “OK”. 13. Close the test program; turn the reader to “OFF” and unplug it from PC. Page 11 of 20 info@acs.com.
3.0. USB Mode Driver Installation 1. Connect the ACR3901U-S Reader and plug the USB cable into PC, if the PC could not install the driver “Microsoft Usbccid Smartcard Reader (WUDF)” automatically. User needs to unzip and use the driver under ACR3901U-S1_TestProgram\USB_Mode\USBModeDriver\ 2. At Computer icon, right click on “Computer” select “Properties” 3. Select “Device Manager” Page 12 of 20 info@acs.com.hk Version 1.00 www.acs.com.
4. Check Smart card reader, use the mouse to right click “ACR3901U ICC Reader”, and select “Update device software…” 5. Select “Browse my computer for driver software” Page 13 of 20 info@acs.com.hk Version 1.00 www.acs.com.
6. Press “Browse” and select the unziped USB Mode driver under the path: \ACR3901U-S1_TestProgram\USB_Mode\USBModeDriver 7. Press “Next”to install the driver. 8. The security window may popup and asks to confirm installation. Press “Install” Page 14 of 20 info@acs.com.hk Version 1.00 www.acs.com.
9. When the driver has finished installation, Press “Close” 10. In device manager, user could check the reader driver with name “ACR3901U ICC Reader” is ready. Page 15 of 20 info@acs.com.hk Version 1.00 www.acs.com.
4.0. Bluetooth Adaptor Driver Installation Bluetooth 4.0 USB Dongle 1. Insert the Bluetooth Adaptor into PC, if the PC automatically popups the driver software installation window, just wait until the driver not successfully installed, press “Close”. 2. Mouse move to Computer, right click on “Computer” select “Properties” Page 16 of 20 info@acs.com.hk Version 1.00 www.acs.com.
3. Select “Device Manager” 4. Check “Other devices”, use the mouse to right click “Unknown device”, Select “Update device software…” Page 17 of 20 info@acs.com.hk Version 1.00 www.acs.com.
5. Select “Browse my computer for driver software” 6. Press “Browse” and select the Bluetooth adaptor driver “ccxxxx_usb_cdc.inf”under the following path: \ACR3901U-S1_TestProgram\BT_Mode\AdaptorDriver\ccxxxx_usb_cdc.inf 7. Press “Next”to install the driver. Page 18 of 20 info@acs.com.hk Version 1.00 www.acs.com.
8. It the windows security warning message shows as below anyway “to continue the installation. ，select “Install this driver software 9. Wait until the driver updates successfully, the message will shows which COM Port is assigned to the Bluetooth adaptor. (*As the example below, the assigned com port is COM8.) Press “Close” to finish the installation. Page 19 of 20 info@acs.com.hk Version 1.00 www.acs.com.
10. After driver installation successfully finish, user can check the assigned com port again from “Device Manager” Page 20 of 20 info@acs.com.hk Version 1.00 www.acs.com.
