Operation and Maintenance Manual
deposit lead and other substances around, on and in the silencer.
Using, handling and/or cleaning a silencer may result in exposure to
lead and other substances known to cause birth defects, reproductive
harm, cancer and other serious physical injury. Have adequate ven-
tilation at all times and wash hands thoroughly after exposure.
CAUTION! Silencers can become extremely hot while the host firearm
is being discharged. After shooting, allow the silencer to reach ambi-
ent temperature before attempting to remove the silencer from the
firearm. If removal is necessary prior to the silencer cooling to ambi-
ent and/or the tightness of the silencer on the host firearm barrel
must be verified, the use of heat-resistant gloves is mandatory. Han-
dling a hot silencer without heat resistant gloves may lead to skin
burns and/or personal injury.
CAUTION! Always wear eye and hearing protection when discharging
a firearm. Discharging a firearm without wearing eye and hearing pro-
tection may lead to personal injury.
GENERAL DESCRIPTION
Congratulations! You are now the proud owner of the best high-perfor-
mance, user-serviceable, user-configurable sound and flash suppressor
for .30 caliber rifles and carbines available in today’s marketplace. The Ti-
RAID 30 can, in seconds and without tools,be configured as either a di-
rect-thread or fast- attach suppressor. In addition to the ease of configuring
the mounting apparatus, the Ti-RAID 30 can be fully disassembled by the
user with no special tools required. The ability to fully disassemble the Ti-
RAID 30 means users will be able to remove copper and carbon deposits
that are impossible to remove from a fully-welded, sealed suppressor. The
revolutionary design of the Ti-RAID 30 baffle core significantly reduces felt
recoil, environmental disturbance, and aids in the preservation of the hear-
ing of shooters and observers. In numerous circumstances, the Ti-RAID
30 may deliver an overall sound signature below the pain threshold and
risk limit for hearing loss*. The Ti-RAID 30 is constructed entirely of light-
weight, high-strength, corrosion resistant Titanium alloy and features a
PVD finish.
* The cumulative effects of sound on hearing are influenced by multiple
factors, including but not limited to the sound level, the total amount of time
(or number of times) one is exposed, barrel length, type of firearm operat-
ing system, ammunition selection, and the surrounding environment. Also,
unforeseen events, such as case ruptures, can expose the user and by-
standers to sound levels well beyond the level of suppressed fire. For these
reasons, AAC recommends the use of hearing protection, even when
shooting with a suppressor.
INSTALLING A Ti-RAID 30 SILENCER ONTO A HOST FIREARM
-90 TOOTH RATCHET TAPER FAST-ATTACH CONFIGURATION-
WARNING! Never attempt to attach a Ti-RAID 30 to a BLACKOUT Si-
lencer-Mounting muzzle device with threads that are dirty or dam-
aged, as this may lead to property damage, personal injury and/or
death.
WARNING! Never attempt to attach a Ti-RAID 30 with dirty or dam-
aged threads to a BLACKOUT Silencer-Mounting muzzle device, as
this may lead to property damage, personal injury and/or death.
WARNING! Never use a silencer with an obstructed bore, as this may
lead to property damage, personal injury and/or death.
1. Always keep the firearm pointed in a safe direction.
2. Render the firearm safe by removing the magazine, completely unload-
ing the firearm and engaging the safety mechanism to the "SAFE" po-
sition. See the firearm's owner's manual for detailed instructions.
3. Inspect the ACME thread on the
exterior of the 90T Ratchet
Taper BLACKOUT Silencer-
Mounting muzzle device, the
toothed gear behind the
threads, and the silencer align-
ment surfaces to verify they are
clean and undamaged. See Fig-
ure 1.
4. Verify the fast-attach mount is
compatible with the 90T Ratchet Taper BLACKOUT Silencer-Mounting
muzzle device mounted to the host firearm. The fast-attach mount des-
ignation is marked on the mount. See Figure 2.
SILENCER MODEL Ti-RAID 30 P.3 SILENCER MODEL Ti-RAID 30 P.4
Figure 1
Silencer
Alignment
Surfaces.
ACME
Thread
90 Tooth
Gear