TM-HALCYON® TECHNICAL MANUAL FOR OPERATION AND MAINTENANCE OF SILENCER MODEL HALCYON ® Printed in the U.S.A. 415452 REV-12.
ADVANCED ARMAMENT CORPORATION Limited Lifetime Warranty for Silencers ADVANCED ARMAMENT CORP. (“AAC”) warrants to the original purchaser (“Purchaser”) of a new Silencer from AAC that such Silencer shall be free from defects in material and workmanship for the duration of time that the Purchaser originally owns that Silencer. AAC, in its sole discretion, shall repair or replace the Silencer if the Purchaser submits a valid warranty claim in accordance with these instructions.
SILENCER MODEL HALCYON 1. 2. 3. 4. 5. P.1 THE TEN COMMANDMENTS OF FIREARM SAFETY Always keep the muzzle pointed in a safe direction. Firearms should be unloaded when not actually in use. Do not rely on your firearm's safety. Be sure of your target and what is beyond it. Only use ammunition that exactly matches the markings on your firearm. 6. If your firearm fails to fire when the trigger is pulled, handle with care. 7. Always wear eye and hearing protection when shooting. 8.
SILENCER MODEL HALCYON CALIBER 22 S/L/LR 22 WMR 17 HMR 17 M2 5.7 x 28 ACTION TYPE BOLT ACTION, SEMI/FULL AUTO BOLT ACTION, SEMI AUTO BOLT ACTION, SEMI/FULL AUTO BOLT ACTION, SEMI/FULL AUTO BOLT ACTION, SEMI/FULL AUTO P.3 MINIMUM BARREL LENGTH 4 INCH 5 INCH 16 INCH 16 INCH 5 INCH WARNING! Do not use this silencer with ammunition and host firearms that fall outside the list in the chart above.
SILENCER MODEL HALCYON P.5 firearm's owner's manual for detailed instructions. 3. Securely tighten the silencer onto the host firearm's muzzle threads in the direction indicated in Figure 1. REMOVING YOUR HALCYON FROM A HOST FIREARM 1. Always keep the host firearm pointed in a safe direction. 2. Render the firearm safe by removing the magazine, completely unloading the firearm (chamber and magazine) and engaging the safety to the "SAFE" position.
SILENCER MODEL HALCYON 4. Insure the three baffles in the front module are rotationally tabbed to the four baffles in the rear tube by holding the rim of the cone of the front-most baffle in the front tube and rotating the three baffles in the front module until the alignment tab on the rear face of the rearmost baffle in the front tube engages the alignment notch on the cone of the front-most baffle in the rear tube. See Figure 8. 5.
SILENCER MODEL HALCYON number for the thread Figure 15 adapter bore is 9464K71. See Figure 13. 3. Using a paper towel or shop cloth, clean the threads on the rear of the main tube body. See Figure 14. P.9 Threads 7. Lubricate the threads inside the lock ring with a thin coat of white lithium grease or Notch anti-seize compound. See Figure 18 Figure 18. 8. Install the wave spring on the thread adapter shaft. See Figure 19. 9.
SILENCER MODEL HALCYON P.11 6. Pushing from the rear (ex- Figure 22 ternal thread end) the three baffles from the front tube and separate them. See Figure 23. WARNING! Only use solvents in a well-ventilated area away from open flames. Unsafe use of solvents may lead to property damage, personal Figure 23 injury and/or death. WARNING! Always wear protective gear, such as eye protection and solvent-resistant gloves when working with any solvent.
SILENCER MODEL HALCYON P.13 7. Using a paper towel or shop cloth, clean the threads inside the lock ring. See Figure 16. 8. Lubricate the threads on the Figure 28 interior of the front module and the rear main tube with a light coat of white lithium grease or anti seize compound. See Figure 28. Lubricate Threads WARNING! All traces of solvent must be allowed to evaporate completely prior to reassembly.
SILENCER MODEL HALCYON P.15 6. Slide the main tube body Figure 34 over the baffle stack. See Figure 34. 8. The baffle stack for the front module is comprised of two standard baffles, and the Figure 35 transition baffle. See Figure Main Tube 36. Body 9. Slide the assembly of the rear main tube and front module over the assembled front module baffle stack. See Figure 37. Figure 36 10. Turn the assembled rear main tube and front module upright.
