PROFESSIONAL SERIES Owner’s Guide For Model: CA RS Deluxe Vehicle Remote Start and Keyless Entry System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2017 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control..................................................................... 3 Using the Keyless Entry..................................................................... 3 Two Stage Door Unlock (optional)...................................................... 3 Activating Trunk Release (optional).................................................... 3 Activating AUX 1 (optional).................................................................
Using Your Remote Control Using the Keyless Entry The button is used to lock the vehicle’s doors, the button is used to unlock the vehicle’s doors. To lock or unlock the doors simply press and release the desired function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked. NOTE: The system is equipped with a feature called Silent Choice.
Programmed Transmitter Notification As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.
Basic Security (Optional Programming Feature) The basic security feature of the system will monitor the vehicle’s doors and ignition circuit and will sound the alarm in the event of unauthorized entry. Note that this feature is defaulted OFF and must be turned on in feature programming. This feature may also require additional parts and or labor at the time of installation. Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button.
Using Your Remote Starter Remote Start Ready Mode must be enabled if your vehicle is equipped with a manual transmission. Remote Start Ready Mode - Manual Transmission Vehicles Only To activate the remote start function, the system must first be in Remote Start Ready Mode. Follow the steps below to enter remote start ready mode. 1. While the engine is running by the ignition key; a. Place the transmission in neutral. b. Set the parking brake 2.
Remote Starting Your Vehicle To activate the remote start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
Using the “Quick-stop” Feature If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage Quick Stop: 1. Stop the vehicle and place the transmission in PARK. 2. With your foot off the brake pedal, press and release the button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered. 3.
User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes.
Remote Start Safety Features For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur: 1. The vehicle’s hood is open. 2. The brake pedal is pressed prior to turning the ignition key to the ON position. 3. The engine is over-revved (tach checking only). 4. Valet Mode is active. Refer to the Valet Mode section of this manual on page 4. Remote Start Ready Mode is not set.
System LED, Light Flashes, and Siren/Horn Indications Status LED Flash Indications LED Flashes Function OFF Disarmed / Unlocked Slow Flash Armed / Locked Fast Flash Passive Arming Countdown ON (Solid) Valet Mode 2 Flashes Zone 2 Trigger, Hood / Trunk 3 Flashes Zone 3 Trigger, Door 5 Flashes Zone 5 Trigger, Ignition Siren/Horn Chirp Indications Chirps Function 1 Disarm / Unlock 2 Arm / Lock 3
Optional 2-Way LED Remote Control Optional 2 Way LED Remote Control Notifications / Responses The 2 Way LED remote control responses outlined below are in addition to the normal beep/LED flash that takes place upon pressing the buttons of the remote control.
Optional 2-Way LCD Remote Control Additional Features of the Optional 2 Way LCD Remote Control Check Vehicle Status Press and release 2 times then press display the current status of the vehicle. within 3 seconds, the transmitter will Display Illumination Press and hold the button for 1 second. The display will illuminate for 5 seconds.
Button Lock Press and release then press hold the for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked. Illumination Press and release 2 times then press and hold for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
LCD Remote Control ICON’s LOCK UNLOCK TRUNK RELEASE VALET MODE TRANSMITTING PANIC ENGINE RUNNING TIME DISPLAY BATTERY INDICATOR BATTERY SAVE MODE TIMER / TEMP START MODES TIME COUNT DOWN VIBRATE/SILENT MODE MELODY MODE 2 CAR MODE ALARM CLOCK 2017 Voxx Electronics Corporation. All rights reserved.
Remote Control Buttons & Functions 4-Button Transmitter Lock Lock Unlock Car Find / Panic Start N/A X Operation Method Press and Release Unlock X Press and Release Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shut Down X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times.
Replacing Remote Control Batteries 4 Button Remote Control - Model CAT4M & CATMLED The batteries inside each remote control should last approximately 1 year for the CAT4M and 6 Months for the CATMLED under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim.
LIMITED LIFETIME WARRANTY Applies to Code Alarm Series Control Modules, Sirens, Sensors, and Relays.
2017 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
