RF-4250 PROFESSIONAL VEHICLE SECURITY SYSTEM OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 4250 Rev.
016/7/19 TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock Doors & Arm System Panic function + - - + + + Car Locator Arm and Delete The 2 Stage Shock Sensor Silent Arming / Disarming Unlock Doors & Disarm System Two Step Door Unlock & Disarm System Trunk Release (Channel 3) Passive Arming By-pass Silent Arming/Disarming 4th Channel 5th Channel Switching code For 2nd Car Operation.
2016/7/19 System Arm AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Door Ajar Trunk / Hood Ajar SILENT ARMING / DISARMING: Press the button or + buttons together on the transmitter on the transmitter to arm or disarm your security system with no chirp sound heard; arm / disarm confirmation will be through the vehicles parking lights only.
2016/7/19 button on the transmitter. 1. Press the 2. The siren will chirp twice and parking lights will flash twice to indicate that the security system is now disarmed. The vehicle doors will unlock and disarm when interfaced with the security system . Trunk/Hood Doors Shock Sensor System Trigger Trigger Trigger Disarm Ignition Trigger TAMPER DISARMING: If the alarm is triggered; upon disarming of the system, the siren will chirp 4 times and parking lights will flash 3 times.
2016/7/19 The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.
2016/7/19 TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impacts will trigger the warn-away signal. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking lights will turn on to alert of an intrusion for 30 seconds. Then the siren will stop and automatically reset and re-arm.
2016/7/19 Driver Paging (For 2-way remote operation only) It is useful in the even that someone wants to page the driver of the parked button vehicle, with the ignition switch in the “ off” condition, press the on the windshield antenna once to page the driver, one chirp sounds shall be emitted from the vehicle and the paging melody continues sounding from your LCD remote, AND “CAL” show on the LCD remote. IGNITION CONTROL DOOR LOCKS.
2016/7/19 Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. AAA BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery icon shall be weakens a displayed on the LCD screen.
2016/7/19 Door Lock Your vehicle doors are locked. Door Unlock Your vehicle doors are unlocked PASS 1 Sensor Bypass Sensor 1 bypass under Arm mode Remote Transmission You are transmitting the signal to control unit Valet Mode All the function shall be temporarily on hold. * In – Range Indicator You are within the remote control range. Low Battery You have to replace the battery of remote control. Ignition On Trunk Release Trunk open. Trunk symbol only. 0:10 4250 Rev.
2016/7/19 * The unit will automatic perform one time HHU in range check, indicate proper icon on LCD display, after that you need to operate HHU for them. PROGRAM MODE 2-WAY LCD REMOTE TRANSCEIVER: PROGRAMMING 2-way LCD HHU: Enter: 1. Press and hold + button until 2 beeps heard then release the + button. (LCD display show Hours of current time set up, set up hour(s) first.) 2. Press button to increase value, or Enable the selected feature. 3. Press button to decrease value, or Disable the selected feature.
2016/7/19 Adjust Alarm Clock minutes from 0 to 59 Select Alarm Clock Enable or Disable 3 4250 Rev.A Parking Meter countdown Adjust Parking Meter countdown hours from 0 to 2 Adjust Parking Meter countdown minutes from 0 to 59. 12: 00 00 is flashing On + Press button => (+) or Press button => (-) Press button confirm its selection, move to next option. or OFF Press button => Enable or Press button => Disable Press button confirm its selection, move to next option.
2016/7/19 Select Parking meter countdown Enable or Disable 4 Power Save Select Power Save Enable or Disable ON + or Press button => Enable or Press button => Disable Press button confirm its selection, move to next option. There is a beep sound at 5 min. before Parking countdown reach 0. Default is OFF OFF On + or Press or Press button => Enable button => Disable When power save enable, the LCD remote transceiver uses “0” current to save the battery power. LCD show “Save” on text area 5 4250 Rev.
2016/7/19 Select 2way HHU confirmation by Melody or Vibration 6 Second Car Security Option Car Select or + or C1 or C2 CAR 1 or CAR 2 ( II icon On) Press button => Melody or Press button => Vibration Press button confirm its selected, move to next option. Default is CAR 1 - CAR 1 operation. - CAR 2 operation (II icon On mean 2nd car operation). Press button confirm its selected, move to next option.
2016/7/19 transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming parameters are the same except for the following: For Regular Remote Control Transmitter: Prior to press any button on the transmitter. Press the + first on the standard transmitter. Once + button is pressed the LED on the transmitter will illuminate for 3.5 seconds.
2016/7/19 While the power save mode, the LCD remote transceiver “sleep” until a button is pushed, extends the life of battery. When power save mode is “Off”, the remote control will wake up periodically to check for messages from the security module.
2016/7/19 Slow flash Fast flash On (solid) Armed Passive arming Valet mode pause 3 flashes... pause 4 flashes... pause 5 flashes... pause Trigger on door switch Trigger on Dual Zone Shock Sensor Trigger on Ignition switch FCC statement This device complies with Part 15 of the FCC Rules.
