Owner’s Guide for models: CA2LCD CA2RELCD Flashlogic FLRS / AS9234E RF Upgrade Kit IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. CA4B - CA2LED Owners rev A.
Table of Contents Flashlogic Functionality..............................................................3 Using Your Remote Control........................................................3 Remote Start Valet Mode.............................................................4 2 Way LCD Transmitter Functions.............................................5 Transmitter Programming...........................................................6 2 Way LCD Transmitter Icon’s..............................................
Flashlogic Functionality Using Your Remote Control Door Lock To lock the vehicle doors press and release the button. Door Unlock To unlock the vehicle doors press and release the button. Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors.
Entering the Vehicle while it is Running via Remote Vehicle Start 1. Unlock the vehicle’s doors. 2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! 3. Insert the key into the ignition switch and turn to the ON or RUN position. 4. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally. Preheating or Precooling the Vehicle’s interior Before exiting the vehicle, set the temperature controls to the desired setting and operation.
2 Way LCD Transmitter Functions Display Illumination Press and hold the button for 1 second. The display will illuminate for 5 seconds. Melody / Vibration Mode To have the remote control vibrate, play a melody tone or both each time it receives a response from the vehicle press and release then press and hold for 2 seconds. Button Beeps To toggle button beeps on or off press and release seconds.
Parking Meter Countdown The parking meter countdown timer has 6 preset times, to access the preset times and begin countdown press and release then press and hold for 2 seconds, each additional press of will increase the countdown time. Adjusting the Clock and Timer Settings The clock, alarm clock and programmable countdown timer are accessed through the Function Menu.
2 Way LCD Transmitter Icon’s NOTE: Icons shown below are only be available when the host system connected supports the available feature. Refer to the host system’s installation/user guide for details of supported features.
Replacing Remote Control Batteries 2 Way LCD Remote Control - Part # CATLCD The AAA battery inside the 2-way LCD remote control should last approximately 6 months under normal use. When the battery becomes weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the BATTERY icon on the LCD remote control will show 1 bar or less. 1. Gently slide the battery cover off of the remote control. 2.
AS9234E Functionality Note: The follow instruction is for you with the AS9234E system only and is separate from the Flashlogic FLRS functionality previously listed in this guide. Operating the AS9234E System Door Lock To lock the vehicle doors press and release the button. Door Unlock To unlock the vehicle doors press and release the button. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the seconds will open the vehicle’s trunk or hatch.
Remote Start Shutdown: To cancel the remote vehicle start function, press and release the within 2 seconds. button 2 times Timed Start Program: The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is useful in extremely cold climates where starting the engine is the only means to keep the battery charged and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48 hours.
Remote Start Override Mode (Valet Mode) - AS9234E The intent of the remote start override / manual shut down circuit is to allow the vehicle operator to prevent operation of the Remote Start Unit regardless of the RF transmitter operation. Enter Remote Start Override: 1. With the system disarmed/unlocked, and the ignition switch off Press and Hold the PBLED push button switch (dash mounted). Turn the ignition switch on, off, on, off, on, off. 2. 3.
Manually Overriding Your Alarm System (Alarm Systems Only): Using the Dash Mounted PBLED Push-Button Valet/Override Switch your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To bypass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the on position. 3.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths. NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory preassigned code of 11 to “52” you would do the following: 1.
Manually Overriding Your system - Using the Custom Code: Assuming the override code programmed has not been changed, and the default override code of 11 is in the system’s memory. 1. Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound. 2. Within 5 seconds, press and release the Receivers push-button switch 1 time. 3. Within 5 seconds, turn the ignition switch off then on. 4.
CA4B - CA2LED Owners rev A.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
