PROFESSIONAL SERIES Owner’s Guide for models: ca5354 Deluxe Vehicle Remote Start System with 900Mhz 2 Way Confirming LED Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2015 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control..................................................................... 3 Using the Keyless Entry..................................................................... 3 Two Stage Door Unlock (optional)...................................................... 3 Activating Trunk Release (optional).................................................... 3 Activating AUX 1 (optional).................................................................
Using Your Remote Control Using the Keyless Entry The button is used to lock the vehicle’s doors, the button is used to unlock the vehicle’s doors. To lock or unlock the doors simply press and release the desired function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked. NOTE: The system is equipped with a feature called Silent Choice.
Programmed Transmitter Notification As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance. Valet Mode Valet Mode is used to disable the system from remote starting.
Using Your Remote Starter Remote Start Ready Mode must be enabled if your vehicle is equipped with a manual transmission. Remote Start Ready Mode - Manual Transmission Vehicles Only To activate the remote start function, the system must first be in Remote Start Ready Mode. Follow the steps below to enter remote start ready mode. 1. While the engine is running by the ignition key; a. Set the parking brake b. Place the transmission in neutral. 2.
Remote Starting Your Vehicle To activate the remote start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes.
Temperature Start Mode The system has the ability to start the vehicle if the temperature drops below a preset temperature threshold. Once activated, the system will only start the vehicle one time based on the temperature setting and will be cancelled if the vehicle is started with the key or remote started by the transmitter. Temperature is read from the module, located below the dashboard in most instances, and the vehicle’s interior temperature may vary from the ambient temperature. 1.
Transmitter Button Functions 1 Way Transmitter Lock Lock Unlock Car Find / Panic Start N/A X Operation Method Press and Release Unlock X Press and Release Trunk X Push and Hold (3 Sec) Car Finder X Panic X Press and Release Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shut Down X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times.
2 Way Transmitter Notifications FUNCTION BEEPS / LED FLASHES Lock 2 Beeps / Flashes Unlock 1 Beep / Flash Trunk Release 1 Beep / Flash if vehicle is currently locked.
Replacing Remote Control Batteries 1 Way 4 Button Remote Control - Model CAT4 The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Using a coin, disassemble the halves of the remote control. 2.
LIMITED LIFETIME WARRANTY Applies to Code Alarm Series Control Modules, Sirens, Sensors, and Relays.
2015 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
