User's Manual

ManualsBrandsAdvance Security ManualsElectronicsRemote Control

NOTE: The Remote Start Unit will not start

or shutdown

the vehicle if any

one of the following

conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. The gear selector is in any gear other than “PARK” or “NEUTRAL”

4. The system in valet mode.

5. Release the parking (hand) brake. (For Standard Transmission Gear Vehicle or Turbo Timer Mode)

6. The system is failed in engine start memorize set up (For Standard Transmission Gear Vehicle.)

7. If the vehicle failed to start, the above status will flash on the LCD screen

SAFE START (Child safety mode)

Factory default is set to press the

button once on the transmitter to start the vehicle. You can program

this feature to eliminate an accidental remote start:

1. The user presses the transmitter buttons twice within 3 seconds to start the vehicle. or

2. The user presses the transmitter and buttons at the same time to start the vehicle.

NOTE: Contact your installing dealer to activate this feature.

OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:

To operate the vehicle while the engine is running from the remote start,

1. Insert the ignition key and turn it to “ON” (not the start) position.

2. Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.

TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been removed from the ignition. This

feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would

like to leave the motor running and the climate control on.

1. Before turning off the engine, press the button once on the transmitter and the LED indicator will

flash 3 times to confirm enter.

2. Turn the ignition key to OFF position. (The engine will stay running.)

3. The engine will run until the pre-programmed time elapsed or shutdown input is received.

TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press button once on the remote transmitter under the remote start mode.

2. Move the optional remote start enable toggle switch to OFF position. (If installed)

3. Press the brake pedal

The vehicle will shut down and turn off the parking light to indicate the engine has stopped.

4. Pull down the hand brake. (for Standard Transmission Gear Vehicle)

The vehicle will shut down and turn off the parking light to indicate engine stopped

2-way LCD REMOTE CONTROL TRANSCEIVER OPERATION:

Table 1:

nter : Press & hold “ F “ button until one beep, release F-button and continue press F button within 5 sec.

to move forward to feature option you want to program.

EXIT: Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

F Button LCD Display Button

Press and hold the

Button

until 1 beeps sound

SENSOR

BYPASS

and

PASS 1 icon On

Press button Enable to arm

the alarm and bypass sensor 1.

Press

Button 2nd time

(HHU 1 beep) within 5

seconds

HIDDEN

ALARM

and

icon On

Press button Enable to arm

system and with Hidden Alarm

Function.

Press

Button 3rd time

(HHU 1 beep) within 5

seconds

ANTI

HIJACK

and

icon On

Under ignition in "on" position

Press button Enable to

activate anti carjacking functions.

Press

Button 4th time

(HHU 1 beep) within 5

seconds

CH 4

flashing

Press button Enable CH#4

output

Note : Press and release F Button 2-way LCD Backlight turns on for 5 seconds

Table 2 :

Enter : Press & hold “ F “ button until 2 beeps heard, release F-button. Continue press F button within 5

sec. to move forward to feature option you want to program.

EXIT: Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

F Button LCD display Button

Press and hold the F Button until

2 beeps sounded

MENU flashing

Press button to enter 2-way HHU menu

mode

Press F Button 2

time (HHU 1

beep) within 5 seconds

STATUS CHECK

Press button Enable to check the

vehicle’s status.

Press F Button 3rd times (HHU 1

beep) within 5 seconds

ALARM CHECK

Press button Enable to check vehicle’s

trigger status.

Press F Button 4th times (HHU 1

beep) within 5 seconds

VOLTS CHECK

Press button Enable to check vehicle’s

Voltage.

Press F Button 5th time (HHU 1

beep) within 5 seconds

TEMP CHECK

Press button Enable to check temp.

status

PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case of

emergency.

1. Press and hold the button for 3 second. The alarm will immediately sound.

2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter

and buttons can be used to lock and unlock the door (if the option is installed), however once the

button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged

allowing the vehicle to start.

3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3

seconds. Also, if any transmitter buttons other than

or button is pressed and released, the

panic mode will be turned off immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows:

Light impact will trigger the warn-away signal.

Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning

on the ignition key will trigger the programmed sequence.

The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn,

parking lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and

automatic reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will

sound a maximum of 3 times of 30 seconds cycles.

DISARMING WITHOUT A TRANSMITTER

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to the 'ON’ position.

2. (Alarm will sound.)

3. Within 10 seconds push and release the antenna mounted valet switch. The alarm will stop sounding

and enter the disarm mode. You can now start and operate the vehicle normally.

SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)

By Table – 2, press and hold F button of LCD remote until 2 beeps heard, release and re-press F button

2 more times, the LCD display show “ALARM CHECK “ on text field (see Table 2), then press

button to activate system trigger check.

Note: If it has no response then you are out of range.

SYSTEM’S STATUS CHECK (For two-way transceiver operation only)

By Table – 2 press and hold F button of LCD remote until 2 beeps heard, release and re-press F button

one more time, the LCD display show “STATUS CHECK “ on text field (see Table 2) then press

button to activate system status check.

Note: If it has no response then you are out of range.

DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)

The alarm has a unique feature that will turn on your vehicle dome light as follows:

1. Upon disarming, the interior light will remain on for 30 seconds.

2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.

Note: Turning on the ignition switch or arming the alarm will turn off the dome light.

CHANNEL 4 TIMER CONTROL OUTPUT

Press remote transmitter and buttons at the same time to active Channel 4 function. Or ref. Table –

1, Press and hold F button of LCD remote until 1 beep sound heard….(see Table 1) then press button

to activate channel 4 function.

Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground

signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used

to turn on the headlight, power window or sunroof. (Factory defaults setting at 1 sec. pulse output.)

POWER SAVER MODE (Default OFF)

Press & hold button + for 5 seconds (chirp x 3) enable Power Save mode. LCD remote

transceiver uses “0” current to save the battery power.

Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”.

TO REMOTE START THE VEHICLE:

When you want to start your vehicle,

1. Press button once on the transmitter.

2. The parking light will activate to indicate the remote start received the signal.

3. The engine will start in approximately 5 seconds.

4. Once the engine is running, after couple seconds the parking lights will turn on and the climate

controls will activate and adjust the vehicle’s interior temperature to your preset setting. (While the

vehicle is running, the “

” icon and the “minutes” digit on the LCD screen will flash and the will indicate

countdown timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.)

5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit

shuts off the countdown timer will turn off and the transmitter will play a melody.)

Table

: Return 2

way HHU to default setting

Enter : Press & hold “ F “ button until 4 beeps heard, release F-button.

EXIT: Press & release " F " button or do nothing wait for 5 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Button

LCD display Button

Press and hold the

Button until 4

beeps sounded

RESET

flashing

Press & hold button for 2 seconds to back to

default setting and 1 chip for confirm

2-way LCD HHU PROGRAMMING (Select and Adjusting Table-2-Menu options):

Enter:

Press and hold F button until 2 beeps heard then release the F button.

The Display will show MENU flashing, press

button to enter HHU menu mode.

(LCD display show Hours of current time set up, set up hour(s) first.)

Press button to increase value, or Enable the selected feature.

Press button to decrease value, or Disable the selected feature .

Press button to confirm its selection, move to the next option.

EXIT: Press & hold " F " button or do nothing wait for 15 sec. automatic exit

2-way LCD (1 beep) => Confirm Exit.

Menu Option LCD display

Functions

Current time set up

Default is 12:00

Adjust clock hours from 0

to 12

: 00

12 is flashing

Press button = (+) or Press button = (-)

Press button confirm its selection, move to next option.

Adjust clock minutes from

0 to 59

12:

00 is flashing

Press button = (+) or Press button = (-)

Press button confirm its selection, move to next option.

Alarm

Clock

set up

Default is OFF

Adjust Alarm Clock hours

from 0 to 12

:00

12 is flashing

Press button = (+) or Press button = (-)

Press button confirm its selection, move to next option.

Adjust Alarm Clock

minutes from 0 to 59

12:

00 is flashing

Press button = (+) or Press button = (-)

Press button confirm its selection, move to next option.

Select Alarm Clock

Enable or Disable

ON + or OFF

Press button = Enable or Press button = Disable

Press button confirm its selection, move to next option.

arking

ter

countdown

PARK METER

Default is OFF

Adjust Parking Meter

countdown hours from 0

to 2

:00

0 is flashing

Press button = (+) or

Press button = (-)

Press

button confirm its selection, move to next option.

Adjust Parking Meter

countdown minutes from

0 to 59.

0 :

30 is flashing

Press button = (+) or Press button = (-)

Press button confirm its selection, move to next option.

Select Parking meter

countdown Enable or

Disable

P-- ON + or

P -- OFF

Press button = Enable or Press button = Disable

Press button confirm its selection, move to next option.

There is a beep sound at 5 min. before Parking countdown reach 0.

Power Save

Default is OFF

Select Power Save

Enable or Disable

+ or

Press button = Enable or Press button = Disable

When power save enable, the LCD remote transceiver uses “0”

current to save the battery power. LCD show “Save” on text area

Exit: Press any button of LCD remote to exit the “Power Save Mode”.

Press button confirm its selection, move to next option.

way HHU Response

mode

or VIB

Default is Buzzer

Select 2-way HHU

confirmation by Melody or

Vibration

+ or

VIB + or

BZ+VIB + +

Press button = Melody or

Press button = Vibration

Press button confirm its selected, move to next option.

6 Second Car Security

Option

CAR SELECT

Default is CAR 1

CAR 1

CAR 2

- CAR 1 operation. - CAR 2 operation

7 Illumination Menu

Default is

3 SEC. o

5 SEC. or

OFF

, Basic operation with backlight Illumination 3 SEC. or 5 SEC.;

OFF – basic operation without backlight

illumination.

8 Key Lock

KEY LOCK

Default is OFF

Key lock enable

or disable

Press button = Enable or Press button = Disable

9 CAR ICON Illumination*

LCD icon

Default is OFF

appear or not

Press button = Enable or Press button = Disable

10 (Time adjust for Daily

Start mode)

icon flashing

Default is OFF

1 -12

12 : 00

12 is flashing

, - Program Daily start hour Press button = (+) hours

increase or Press button = (-) hours decrease

0 - 59

12 : 00

00 is flashing

, - Program Daily start minute Press button = (+)minutes

increase or Press button = (-)minutes decrease

* Car LCD icon is programmable show car icon on LCD display always or appear it needed as below.

(system trigger / valet mode / zone ajar/ anti car-jacking mode car LCD will show on LCD display).