User's Manual
9
3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds. Also, if
any transmitter buttons other than or button is pressed and released, the panic mode will be turned off
immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
L. TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning on the ignition
key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking
lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and automatic
reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will sound a
maximum of 3 times of 30 seconds cycles
NOISE ABATEMENT CIRCUIT: Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive
trigger sequences due to faulty door pin switches or environmental conditions such as thunder,
jackhammers airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor
or switch has triggered the alarm; the “Noise Abatement Circuit” will interpret this pattern of triggers as a
false alarm. After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses, that sensor or
switch until a different sensor or switch is trigger.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door
for 3 full cycles, the doors will be bypassed until the trigger ceases.
M. ANTI HI - JACKING
Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature
“OFF”. This system is default setting all cars jacking “OFF”.
ACTIVE ANTI CAR JACKING:
1.Under ignition on press
F button four times while “CAR JACK” flash on text area(see Table 1), then
press
button for 2 seconds to activate Anti Car-Jacking mode or
Under ignition on press and hold the
and buttons at the same time for 2 seconds. The parking
lights will turn on for 1.5 seconds to indicate the system enter the anti car-jacking mode.
2. Once the system is in anti car-jacking mode, the system will be triggered when the door is opened
and closed while the ignition is “ON”.
PASSIVE ANTI CAR- JACKING:
It will operate as noted below:
1. Turn the ignition switch to the “ON” position and the system will arm.
2. Once the system is armed, if you are forced from the vehicle, the system will trigger when the door is opened and
closed while the ignition is “ON”.
TRIGGER THE ANTI CAR -JACKING MODE:
a). 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.
b). During this 15 second period of chirping, you will be alerted to push the valet switch once to turn off the car-jacking
feature. If not, it will enter a second timer for car jacking.
c). 65 seconds after the system has been triggered, the siren will start sounding and the parking lights will start
flashing.
d). 90 seconds after the system has been triggered,
1. The siren will sound and the parking lights will flash, and
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power is exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system
disarmed
Note: If you use password pin code to double protect the vehicle security, you will need to use it to completely disarm
the system.
N. SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
By Table – 2, press and hold F button of LCD remote until 2 beeps heard, release and re-press F button
2 more times, the LCD display show “ALARM CHECK “ on text field (see Table 2), then press
button to activate system trigger check.
Note: If it has no response then you are out of range.
O. SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
By Table – 2 press and hold F button of LCD remote until 2 beeps heard, release and re-press F button
one more time, the LCD display show “STATUS CHECK “ on text field (see Table 2) then press
button to activate system status check.
Note: If it has no response then you are out of range.