User's Manual

ManualsBrandsAdvance Security ManualsElectronicsRemote Control

REMOTE ENGINE STARTER

WITH ALARM SYSTEM

OWNER’S MANUAL

A. BATTERY REPLACEMENT:

This system needs no specific maintenance beyond remote control battery replacement. The 2-way

remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a 3V, CR2032 battery

Battery Level Indicator (2-way remote)

The Battery Level indicator has three level indicators that serve as a visual indication of battery charge.

When the battery reaches a low charge level that requires replacement, the remote control will generate

a single notification chirp, and the Battery Level indicator

will flash continuously.

Gently pull the end of the battery door away from the top of the remote control then slide the door up to

expose the battery and remove the expired battery. Place the new battery into the remote. When power is

returned the remote control will display all icons in the LCD and generate all beeper tones once. Press

any button on the remote to terminate the beeper tone review.

B. STANDARD LCD ICON CONFIGURATIONS:

The lock icon will be displayed when the

door locked.

The unlock icon will be displayed

when the door unlock

Valet Mode

Remote start and alarm functions shall

be temporarily on hold.

Hidden Alarm Mode

The security system arm with hidden

alarm function

Hood Trigger

Hood is illegally opened (Zone 1)

Trunk Trigger

Trunk is illegally opened (Zone 2)

Door Open Warning

Doors are illegally opened (Zone 3)

Sensor Trigger

Trigger on Sensor 1 (Zone 4)

Summary of content (13 pages)

PAGE 1
REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL A. BATTERY REPLACEMENT: This system needs no specific maintenance beyond remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a 3V, CR2032 battery Battery Level Indicator (2-way remote) The Battery Level indicator has three level indicators that serve as a visual indication of battery charge.
PAGE 2
PASS 1 12:00 Ignition Trigger Ignition switch is illegally turned on (Zone 5) System trigger Remote Transmission You are transmitting the signal to control unit In – Range Indicator Your are within the remote control range. Anti Car-Jack Mode Activate the anti car-jacking mode 2nd Car Operation Engine Cranking Your vehicle engine Cranking by remote control Engine Running Your vehicle's engine is running Timer Control Start Engine start automatically every 2 or 3 hours.
PAGE 3
Press F Button 3rd time ANTI- HIJACK and (HHU 1 beep) within 5 button Enable to activate anti car icon On seconds Press F Button 4th time Under ignition in "on" position Press CH 4 jacking functions. flashing Press (HHU 1 beep) within 5 button Enable CH#4 output seconds Note : Press and release F Button 2-way LCD Backlight turns on for 5 seconds Table 2 : Enter : Press & hold “ F “ button until 2 beeps heard, release F-button. Continue press F button within 5 sec.
PAGE 4
Order Menu Option 1 Current time set LCD display Functions Default is 12:00 up Adjust clock hours 12 : 00 12 is flashing from 0 to 12 Press button = (+) or Press button = (-) Press button confirm its selection, move to next option. Adjust clock minutes from 0 to 12: 00 00 is flashing 59 Press button = (+) or Press button = (-) Press button confirm its selection, move to next option.
PAGE 5
4 Power Save + Select Power Save Default is OFF Press button = Enable or or button = Disable Press Enable or Disable When power save enable, the LCD remote transceiver uses “0” current to save the battery power. LCD show “Save” on text area Exit: Press any button of LCD remote to exit the “Power Save Mode”. Press button confirm its selection, move to next option.
PAGE 6
Remote start Quick feature programming Enter : Press & hold “F” button until 3 beeps heard, release “ F” button LCD highlight flashing icon first, press and release “F” button to move blinking cursor to the desired icon which you want to program. Press button means Enable, 2-way LCD HHU Note: Cursor method: a constant illumination mean the selected feature enable. Exit : Press & hold " F " button for 2 sec. or do nothing wait for 5 sec. automatic exit 2-way LCD (1 beep) => Confirm Exit.
PAGE 7
Activate or Turn Off The Remote Start Press button once. Channel # 4 Timer Output (4) Switching code For 2nd Car Operation. Optional For regular XT-37 remote transmitter Only + + B CHIRP INDICATORS: C. PARKING LIGHT: Chirp Function Parking light 1 chirp Arm 1 flash Function Arm 2 chirps Disarm 2 flashes Disarm 3 chirps Defective Reminder 3 flashes Disarm / Triggered 4 chirps Disarm / Triggered 12 flashes Car Locator 6 chirps Car Locator Constant On Under Remote Start D.
PAGE 8
2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks and dome light must be installed with the security system.) TAMPER DISARMING: If the alarm is triggered upon disarm, the system’s siren will chirp 4 times, and the parking lights will flash 3 times.
PAGE 9
3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds. Also, if any transmitter buttons other than or button is pressed and released, the panic mode will be turned off immediately. 4. If the button is not pressed, the alarm will automatically stop after 30 seconds. L. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: Light impact will trigger the warn-away signal.
PAGE 10
P. DRIVER PAGING / LOSE & FOUND (For two-way transceiver operation only) It is useful the event that someone wants to page the driver of the parked vehicle or someone cannot find his LCD remote transceiver. Under the ignition switch “off” condition, press and hold the valet switch for 3 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD transceiver. Q.
PAGE 11
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls will activate and adjust the vehicle’s interior temperature to your presetting. (While the vehicle is running, the “minutes” digit on the LCD screen will flash and the will indicate count down timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.) 5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down.
PAGE 12
1. Turn Ignition On => Off 2. After above (1) within 15 seconds, (ref. page-6 2-way HHU quick feature programming => Enable Time start.) press and hold F button of LCD remote until 3 beeps sound , release and re-press F button until LCD show “ “ icon flash on LCD remote (see Table 3), then press button to activate Time Start. icon illuminate on LCD display, parking light flash / siren chirp 3 or 2 times confirm.
PAGE 13
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.