User's Manual






















 
CAR LOCATOR
Under armed mode, press the
button to active car locator function. The
siren will chirp 6 times. The parking light will flash 12 times, for you to
easily locate your car.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case of emergency.
Press and hold the
button for 3 second. The alarm will immediately
sound.
To stop the alarm, press the trunk
button on the remote control.
If the button is not pressed, the alarm will automatically stop after 30 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk
open / Turning on the ignition key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from
cranking. The siren, horn, parking lights, and dome light will turn on alerting
of an intrusion for 30 seconds. Then it will stop and automatic reset and re-
arm. If the any one of the sensors or detectors is still active, the alarm
system will sound a maximum of 3 times of 30 seconds cycles.
NOISE ABATEMENT CIRCUIT: Your system has a “Noise Abatement
Circuit”. It prevents annoying repetitive trigger sequences due to faulty door
pin switches or environmental conditions such as thunder, jackhammers
airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times.
Each time, the same sensor or switch has triggered the alarm; the “Noise
Abatement Circuit” will interpret this pattern of triggers as a false alarm.
After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses,
that sensor or switch until a different sensor or switch is trigger.
SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
Press and hold F button of LCD remote until 3 beeps sound , release and
re-press F button again, the LCD remote will show “ALARM “ icon flashing
on text area (see advanced users mode), then press
button to activate
system trigger check.
SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
Press F button of LCD remote until 3 beeps sound , the LCD remote will
show “STATUS “ icon flashing in the text area (see advanced users
mode), then press
button to activate system status check.
It responds with one melody sound and all vehicles’ status records will
immediately displayed on the LCD screen.
Note: If it has no response then you are out of range.
TRUNK RELEASE: Press and hold
button on the transmitter for two
seconds to remotely control the trunk release.
CHANNEL 4,5,6 OUTPUTS.
Press the transmitter
and buttons at the same time to active Channel
4 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 4” icon flash, then press
button to activate channel 4 function.
Channel 4, 5 & 6 are user-programmable timer outputs. You may program
the built-in timer to send a ground signal for any time duration from 1
second to 120 seconds. For instance, this timer output may be used to turn
on the headlight, power window or sunroof. (Factory defaults setting at
momentary output.)
Press the transmitter
and buttons at the same time to active
Channel 5 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 5” icon flash, then press
button to activate channel 5 function.
Press the transmitter
and buttons at the same time to active
Channel 6 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 6” icon flash, then press
button to activate channel 6 function.
Clear the Flashing Icon and Melody Sound: The Transmitter will reset the
flashing icons the next time the Ignition is cycled to the ON position.
Stopping The Trigger Melody Sound: When the alarm is triggered, the LCD
screen will alert the user through a melody sound and a flashing trigger icon.
Press any button on the LCD remote transmitter to stop melody sound only.
Remote Start Operation:
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started
automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or
garage.
5. Always apply the parking brake and lock the vehicle as you exit the
vehicle.
6. The vehicle windows must be rolled up.
7. Should the unit malfunction, disconnect the fuse until the problem is
corrected.
8. The use and operations of this system is the sole responsibility of the
operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
10.It is not safe to remote start the vehicle if the vehicle is parked on a
steep incline.
TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button once on the transmitter.
2. The parking light will activate to indicate the remote start received the
signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will
turn on and the climate controls will activate and adjust the vehicle’s interior
temperature to your preset setting. (While the vehicle is running, the
“minutes” digit on the LCD screen will flash and the will indicate countdown
timer based on the 5, 10, 20 or 30 minute run time set up by your
installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before
shutting down. (When the unit shuts off the countdown timer will turn off
and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle is switched to the “OFF” position.
(If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”.
SAFE START (Child safety mode)
Factory default is set to press the
button once on the transmitter to start
the vehicle. You can program this feature to eliminate an accidental remote
start:
1. The user presses the transmitter
buttons twice within 3 seconds to
start the vehicle. or
2. The user presses the transmitter
and buttons at the same time to
start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:
To operate the vehicle while the engine is running from the remote start,
Insert the ignition key and turn it to “ON” (not the start) position.
Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the
engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you wish
to exit and lock the vehicle for short periods of time, but would like to leave the
motor running and the climate control on.
1. Before turning off the engine, press the
button once on the
transmitter and the LED indicator will flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown
input is received.
TURBO CHARGE MODE:
Turbo charger mode keeps the engine running after arriving at your
destination for a programmable period of 1, 3 or 5 minutes, This allows the
vehicle’s engine time to conveniently cool down the turbo after you have
left the vehicle. For use, Please download the complete manual.
TIMER START: Please download the complete manual.
This unit can be programmed to start and run the engine every 3 hours or
punctually at the same time next morning, the engine will run for the
programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, never
start and run the vehicle in on enclosed space as a garage or carport.
Please be sure you fully understand this feature before use.
TEMPERATURE and VOLTAGE CHECK
Please see advanced user menu below
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
Press
button once on the remote transmitter under the remote start mode.
Press this button twice if the unit is programmed to child safety start.
Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate the
engine has stopped.
SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The parking (hand) brake is released (For Turbo Timer Mode)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Press
button on the remote transmitter under remote start mode.
7. The system triggers.
8. The vehicle refused to start running after {3} unsuccessful
attempts.
ADVANCED USER’S MODE:
LCD REMOTE TRANSCEIVER OPERATION:
Enter: Press and hold F Button until beep sound respond from LCD
transceiver indicate into table 1 – 5 as below.
Exit: Press the
, or button to exit this mode.
Table 1: ONE beep to confirm (Press & hold “ F “ button until 1 Beep is
heard)
F Button LCD Display
Button
Press once Backlight turns on for 5 seconds
Press twice within 5
seconds
PASS and
PASS icon flashing
Press button to arm the
alarm and bypass the sensor 1.
Press three times
within 5 seconds
HIDDEN
A
LARM and
icon flashing
Press button to arm system
and with Hidden Alarm Function.
Press four times
within 5 seconds
A
NTI CAR- JAC
K
and
icon flashing
Ignition in "on" position press and
hold button for 2 seconds to
activate anti carjacking functions.
Table 2: TWO beeps to confirm (Press & hold “ F “ button until 2 Beeps
are heard)
F Button LCD display
Button
Press and hold the F
Button for 2 second until 2
beeps sounded
MENU flashing
Press button to enter the
menu mode
Press one more time within
5 seconds
CH 4 flashing
Press button to activate
channel 4 function
Press twice within 5
seconds
CH 5 flashing
Press button to activate
channel 5 function
Press three time within 5
seconds
CH 6 flashing
Press button to activate
channel 6 function
Table 3: THREE beeps to confirm(Press & hold “F” button until THREE
Beeps are heard)
F Button LCD display
Button
Press and hold the F
Button for 3 second
until 3 beeps
sounded
STATUS and
icon is flashing
Press button to check the Vehicle
Status.
Press ONE more
time within 5
seconds
A
LARM and
icon flashing
Press
button to check the system
trigger condition.
Press TWO more
times within 5
seconds
V
oltage and
Check icon flashing
Press button to check the Vehicle
Battery condition.
Press THREE more
times within 5
seconds
TEMP and
icon flashing
Press
button to check the Interio
Temperature of the vehicle
Press Six more
times within 5
seconds
Start timer and
icon flashing
Press button to activate or cancel
daily start.
Table 4: FOUR beeps to confirm (Press & hold “F” button until 4 beeps
are heard)
F Button LCD display
Button
Press and hold the F
Button for 4 second
until 4 beeps sounded
DEMO mode
Press button to activate Backlight
will be ON until DEMO operation end.
Table 5: Do-Re-Mi sounds to confirm
F Button LCD
display
Button
Press and hold the F Button for 6
second until Do-Re-Mi sounded
DEFLT
flashing
Press & hold button for 2
seconds to back to default setting and
1 chip for confirm
. PROGRAMMING LCD REMOTE (Transmitter Manual mode):
Selecting and Adjusting Menu options:
Press and hold F button for 1 second until 2 beeps sound, then release the F button.
The text will flash on the LCD screen, press button to enter the menu.
Press button to move up in the menu or button to move down in the menu.
Press button to select the option you would like to adjust.
Press button to increase the value, to activate or deactivate a function or to toggle through the
selection.
Press button to decrease the value, to activate or deactivate a function or to toggle
through the selection.
Press button to move to the next sub-option or go back to the main menu.
EXIT: Press button to exit the menu mode.
Trans.
mode
Menu Option LCD displa
y
Functions
1 Parking Menu PARK METER
Default is
- Parking hours
0:30
0 is flashing
, - Adjusts parking hour
(value from 0 to 2).
- Parking minutes
0:30
30 is flashing
, - Adjusts parking minute
(value from 0 to 59).
- Toggle Parking
countdown
+ or
- Enables parking countdown.
There is a beep 5 min. before the
Parking countdown reaches 0.
- Disables parking countdown.
2 Illumination Menu
Default is
- Toggle Illumination
Mode
3 SEC. or
5 SEC. or
OFF
, Basic operation with backlight
Illumination 3 or 5 sec. or OFF
3 Second Vehicle Default is CAR 1
- Car Select
CAR 1 or
CAR 2
-CAR 1 operation.
- CAR 2 operation.
4 Clock Menu
Default is
- Clock hours
12:00AM
12 is flashing
, - Adjusts clock hour from 0 to
12
- Clock minutes
12:00AM
00 is flashing
, - Adjusts clock minute from 0
to 59
5 Alarm Clock Menu
Default is
- Alarm hours
12:00AM
12 is flashing
, - Adjusts alarm clock hour from
0 to 12
- Alarm minutes
12:00AM
00 is flashing
, - Adjusts alarm clock minute
from 0 to 59
- Toggle alarm
ON + or
OFF
- Enable alarm clock or
- Disable alarm clock
6 Confirmation Menu
VIBRATE
Default is
- Toggle Buzzer and
Vibrate
+ or
VIBRATE +
or
+ +
, - Buzzer or Vibration
7 Button Lock Menu
Default is
- Toggle button lock
- button lock / Disable the
transmitter temporarily
- button unlock / Enable the
transmitter function
8 Power Save Menu
Default is
- Toggle power
save
- While the power save mode,
the LCD remote transceiver uses “0”
current to save the battery
power.
- Power save OFF
Exit: Press any button to exit the
“Power Save Mode”.
9 Daily Start Timer Setting
Daily Start Time Adjust Only (ex.
7:30AM)
- Daily Start Hour
7:30AM
7 is flashing
, - Adjusts clock hour from 0 to
12
- Daily Start Minute
7:30AM
30 is flashing
, - Adjusts clock minute from 0
to 59
To Exit: Do not push any buttons for 15 seconds
TRC760A