User's Manual

H6/4 WHITE / BLUE WIRE – (-) Instant Start & Turn Off Input –
This wire activates and turns off the remote starter each time it sees a momentary ground signal. Normally used for testing
during installation or when activating the module from an after-market system.
H6/5 WHITE WIRE – (-) 200mA Dome Light Control Output –
This wire becomes grounded when the
dome light controls circuit active. The
current capacity of this wire is 200mA.
This wire can control the operation of
the interior lights. An optional 10 Amps
relay can be used to this system for
interior lights operation.
87a
86
87
30
85
Fuse
White Wire
+12V
Door
Switch
Courtesy
Light
a). Upon disarming, the interior lights will remain on for 30 seconds.
b). If the alarm is triggered, the interior light will flash for the same duration as the siren.
H6/6 BROWN / WHITE WIRE – (-) 200mA Programmable Output Horn Output – (Factory default setting)
This wire is provided to use the existing
vehicle's horn as the alarm system's
optional's warning audible device. It's a
transistorized low current output, and
should only be connected to the low
current ground output from the vehicle's
horn switch. When the system is
triggered, the horn will sound.
8586
87
87a
30
Brown/White
wire
To horn
+ 12 V
+12V Or Ground
Depending On System
Requirements
FUSE
Factory Security Rearm Signal Output –(See Alarm Feature C – 2 Programming) –
This output is programmable. If programmed rearm a factory installed security system. This wire will supply a pulse whenever
the remote start times out or is shut dowm using the transmitter and remote door locking.
H6/7 BLACK/GREEN WIRE – (-) 200mA Channel 4
See Alarm Feature C – 6 Programming)
Channel 4 Output (Factory default setting ,
Momentary grounded)
This wire is built-in user-programmable timer output provides a ground through this wire. Press the transmitter
and
buttons at the same time. You may program the built-in timer to send a ground signal for any time interval between 1 second
and 2 minutes. For instance, this timer output may be used to turn on the headlight with the remote control. Also on certain
BMW, Mercedes Benz, Jaguar and Volkswagen cars, you can use this unique timed output to allow remote closure of all power
window and sunroof without the need for an external module!
H6/8 BLACK/WHITE WIRE – (-) Neutral Safety Switch Input or (-) Enable Switch Input –
When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote
start is disabled.
1. The optional “remote start toggle switch” can be added on to temporarily disable the Remote Start Device, it can prevent the
vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed
area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. To enable the
remote start, move the optional remote start enable toggle switch to the ON position.
2. If needed, this wire can connect to the PARK/NEUTRAL switch in the vehicle.
(See the TESTING YOUR INSTALLATION GUIDE)
IMPORTANT NOTE: This wire must have a “GROUND” to operate remote start.
H6/9 ORANGE/WHITE WIRE – 200mA Grounded Output when Disarmed - N.O. Disable
This wire will become grounded when the alarm is disarmed. The current capacity of this wire is 200mA. It can be connected to
optional Ignition disable relay / ECU disable relay / Fuel Pump disable relay.
87
87a
85
30
86
IN4003 Diode
H10/19
: Orange/White wire
from control module
“Start”
“On”
X
Cut
“Acc”
“Off”
H1/4
Yellow wire (Ignition 1 output)
form Heavy Gauge wire harness
To Ignition Coil
H6/10 WHITE/RED WIRE – Tachometer Signal Connection –