User's Manual

RPM LEARNING / TACHOMETER CHECKING TYPE
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 11 times and hold it on the 11
th
push until five chirps with a long chirp is hearing then release the valet
switch.
3. Press and release the transmitter and buttons at the same time once to set the “Tachometer Checking Type”. [1] LED
flash, [1] chirp (4 chirps if Data Buss connection us programmed), to confirm this setting.
4. Press and release the transmitter button once, [1] LED flash, [1] chirp to indicate your are in features “RPM Learning
mode”.
5. Start the vehicle with the key. (While the engine is running, the parking & LED will flash, If don’t, please check tachometer
White/Red wire connection. (H6/10)
6. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two seconds. The RPM signal is
learned.
7. Turns off the ignition switch to stop the engine running.
Once you complete step 7, you can adjust and test “Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press button once on the transmitter to start the vehicle.
2. If everything goes well:
a. Press
button once on the transmitter to stop engine running. You have been completed this programming successfully.
b. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking light flashes for
confirmation.
3. If the crank time is too long, (Engine already successfully running, but still cranks):
a. Press
once on the transmitter to stop engine running or press brake pedal.
Press button on the transmitter to set proper “Check Level ” to Low position. [1] LED flash, [1 chirp will confirm this
setting
b. Repeat steps 1 – 4 if necessary.
4. If the crank time is too short, (Engine not running, crank stopped before starting):
a. Press
button once on the transmitter to stop engine running.
Press button on the transmitter to set proper “ Check Level ” to Hi position. [2] LED flash, [2 chirps will confirm this
setting
Repeat steps 1 – 4 if necessary.
VOLTAGE CHECKING TYPE
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 11 times and hold it on the 11
th
push until five chirps with a long chirp is hearing then release the valet
switch.
3. Press the transmitter and buttons at the same time to set the “Voltage Checking Type”. [2] LED flashes, [2] chirps to
confirm this setting
Once you complete step 3, you can adjust and test “Start Timer” as below:
START CRANK TIME PROGRAMMING: (TEST and ADJUST)
1. Press button once on the transmitter to start the vehicle.
2. If everything goes well:
Wait for 15 seconds:
a. If the engine still running.
I. Press button once on the transmitter to stop engine running. You have been completed this programming successfully.
II. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking light flashes for
confirmation.
b. If the engine shuts down after the vehicle has been started.
I. Press
button once on the transmitter to stop engine running.
II. Press button on the transmitter to set “Check Level” to LOW position. [1] LED flash, [1] chirp to confirm this setting
III. Repeat steps 1 – 2.
3. If the crank time is too long, (Engine already successfully running, but still cranks):
a. Press
button once on the transmitter to stop engine running.
b. Press button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm entry. (Decrease “Start
Timer” is necessary.)
c. Repeat steps 1 – 4 if necessary.
4. If the crank time is too short, (Engine not started, crank time stopped):
a. Press
button once on the transmitter to stop engine running.
b. Press button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm entry. (Increase “Start
Timer ” is necessary.)
c. Repeat steps 1 – 4.
Timer Checking Type