User's Manual

1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 7 times (holding in on the 7th push) until three chirps with one long chirp is heard then release the valet
switch. You are now in the Alarm feature “C” programming mode. You can program or delete the password pin code as below:
Program:
1. Press and release the transmitter
button twice, [2] LED flash, [2] siren/horn chirp to indicate that you are in features
“Password Pin Code Programming mode”.
2. Within 5 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet Switch from 1 – 9 times.
3. Within 15 seconds of the last entered 9ths digit, turn the Ignition switch to “ON” position.
4. Within 15 seconds, enter your chosen second 9ths digit by pressing and releasing the valet Switch from 1 – 9 times.
5. Finish by turning the ignition switch to “OFF” position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing the LED, first indicating
the first digit code has been memorized, pause and then the second digit code. The unit will report the new code three times with a
one-second’s pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more then 5 seconds during of above steps, the
unit will revert back to the last successfully stored code. Three long chirps will confirm exit. The unit will revert back to the last
successfully stored code
Delete Password Pin Code / Override without Password Pin Code (Factory default setting):
Within 15 seconds, press and hold the transmitter
button for 3 seconds. One long chirp is heard to confirm Deleted the
Password Pin Code.
Example: To program the Password Code 92, you would;
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 7 times (holding in on the 7th push) it until three chirps with one long chirp is heard, and then release
the valet switch. You are now in the Alarm feature “C” programming mode.
Program:
1. Press and release the transmitter
button twice, [2] LED flash, [2] siren/horn chirp to indicate your are in features “Password
pin code programming mode”.
2. Within 5 seconds, press and release the valet Switch 9 times.
3. Within 15 seconds of the last entered 9ths digit, turn the Ignition Switch to “ON” position.
4. Within 15 seconds press the valet Switch twice.
5. Turn the Ignition Switch to “OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be repeated three times
indicating the new code (92) has been accepted and stored in memory.
Exit: Press any button (except
button) of the transmitter to exit the password pin set up mode.
REMOTE START FEATURE PROGRAM MODE.
START FEATURE “D” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 9 times (holding in on the 9
th
push) until four chirps with one long chirp is heard then release the valet
switch. You are now in the Start feature “D” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
Gasoline Engine
1
+
Diesel Engine
with
Wait-To-Start
Light (H6/12
White/Green
wire must be
connected)
Diesel Engine
without
Wait-To-Start
Light
10 seconds
warm-up timer
Diesel Engine
without
Wait-To-Start
Light
15 seconds
warm-up timer
Diesel Engine
without
Wait-To-Start
Light
20 seconds
warm-up timer
2
Factory alarm
disarm with
channel 3 on
Without this
feature
3
Constant
parking light
output upon
Remote Start
Flashing parking
light output upon
Remote Start
4
20 minutes run
time
30 minutes run
time
10 minutes run
time
5 minutes run
time