User's Manual

ALARM FEATURE: “C” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 7 times (holding in on the 7th push) until three chirps with one long chirp is heard and then release the
valet switch. You are now in the Alarm feature “C” programming mode.
3 Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp / LED
one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps / LED
four pulses
1
H6/3 Pink Wire
=
Two step door
unlock output
H6/3 Pink Wire =
Factory Security
Disarm Signal
Output
H6/3 Pink Wire =
Start Status
Output
(Shock Sensor
Bypass)
H6/3 Pink Wire =
Start Status
Output
(Shock Sensor
Bypass 20 SEC)
2
H6/6 Brown /
White Wire = (-)
200mA Horn
Output
H6/6 Brown /
White Wire =
Factory Security
Rearm Signal
Output
3
Fahrenheit
display for
Temperature
Celsius display
For temperature
4
Override
Without
Password Pin
Code
Override With
Password Pin
Code
5
+
H6/15 Gray Wire
Channel 3
Output =
Pulsed output
H6/15 Gray Wire
Channel 3
Output =
Latched output
H6/15 Gray Wire
Channel 3
Output =
Latched output
and reset with
ignition “on”
H6/15 Gray Wire
Channel 3 Output
= Timer
programming (set
to any interval
between 1 second
and 2 minutes.)
6
+
H6/7 Black /
Green Wire
Channel 4
Output =
Momentary
output
H6/7 Black /
Green Wire
Channel 4
Output =
Latched output
H6/7 Black /
Green Wire
Channel 4
Output =
Latched output
and reset with
ignition “on”
H6/7 Black /
Green Wire
Channel 4 Output
= Timer
programming (set
to any interval
between 1 second
and 2 minutes.)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
Channel 4 Timer Control Output Programming.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 7 times (holding in on the 7th push) until three chirps with one long chirp is heard then release the
valet switch. You are now in the Alarm feature ‘C’ programming mode.
Timer Program:
1. Press and release
and buttons together 4 times, [4] LED flash, [4] siren/horn chirps to indicate that you are in
features “Channel 4 Timer Programming mode”.
2. Press and hold the valet switch, the timer will immediately start.
3. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation. (Set to any interval between 1
second and 2 minutes)
Note 1:
If your built-in timer controls window/sunroof closure in your car DO NOT change the timer setting! This requires installer-only
programming. Changing the value will adversely effect operation and may cause damage.
Note 2:
Momentary output
= The momentary output selection will send a negative signal from the Channel 4 output immediately when the
channel 4 button is pressed and will continue until the button is released.
Latched output
= The latched output selection will send a negative signal as soon as the Channel 4 button is pressed and will
continue until the button is pressed again.
Latched output / reset with ignition
= The latched / reset with ignition output selection operates just like the latched output but
will reset or stop when the ignition is turned on.
Password Pin Code Setup:
Enter: