User's Manual
Table Of Contents
- Door Lock
- Door Unlock
- Your vehicle doors are unlocked and the system is Disarmed
- Armed Mode
- Hidden Alarm Mode
- Activate the car jacking mode
- Valet Mode
- Remote Transmission
- You are transmitting the signal to control unit
- In – Range Indicator
- Hood Trigger
- Trunk Trigger
- Door Open Warning
- Sensor Trigger
- Engine Cranking
- Engine Running
- Timer Control Start
- Engine start automatically at the same time next day or every 2 / 3-hour.
- Indoor temperature of your vehicle
- Activate Channel 4
- Activate Channel 6
- You have set morning call alarm
a. Press the
button twice to stop engine running. You have been completed this programming
successfully.
b. Press button once to exit the program mode and the siren will chirp three long chirps.
3. If the crank time is too long. -- (Engine is successfully running, while the starter is still cranking --:
a. Press the button twice to stop engine running.
b. Press the
button to set proper “Start Timer”. The chirp will confirm these enter.
-- Decrease “Start Timer” is necessary --
c. Repeat the step1 – 4.
4. If the crank time is too short. -- The engine did not successfully run before the starter quit cranking --:
a. Press the button twice to stop engine running.
b. Press
button to set proper “Start Timer”. The chirp will confirm these enter.
-- Increase “Start Timer ” is necessary --
Repeat the step1 – 4.
RETURN TO FACTORY DEFAULT SETTING:
1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position.
2. Push the Valet switch 12 times and holding in on the 12
th
push until six chirp with a long chirp is hearing
then release the valet switch. You are now in the “Return To Factory Default Setting” programming
mode.
ALARM FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:
3. Press and hold the
and buttons at the same time for 5 seconds, there will be a confirmation six
chirp with 3 long chirp to confirm the system “Alarm Feature I & II & III Programming all returns to
factory default setting.
START FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:
4. Press the
first, within 3 seconds press and hold the and buttons at the same time for 5
seconds, there will be a confirmation six chirp with 3 long chirp to confirm the system “Start Feature I &
II Programming all returns to factory default setting.
TEST MODE
In this test mode, this system can test the all of the trigger input. The installer can save time to test the
sensitivity of the 2-stage shock sensor and optional sensor without using the traditional arming/disarming
procedures to test the sensors.
Enter:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
th
push until five chirps with a long chirp is
hearing then release the valet switch. You are now in the Start feature ‘II’ programming mode.
a. Test the Trigger Input:
Press and release
and buttons at the same time once. One chirp to indicate you are in test
mode.
Trigger sensor Siren short chirps
Zone 1 / Hood trigger (H3/4 White/ Black wire) 1
Zone 2 / Trunk trigger (H3/1 Blue wire) 2
Zone 3 / Door trigger (H3/2 Green or H3/3 Violet wire) 3
b. Test the Sensor 1 / Shock Sensor (Connected to H7 4 Pin Plug):
Press and release
and buttons at the same twice. Two chirps to indicate you are in the shock
sensor (connected to H7 4 pin plug) test mode.
1. Activate the warn-away (first stage of the shock sensor); system will emit a short chirp.
2. Activate the full alarm (second stage of the shock sensor); system will emit a long chirp.
3. Continue to test the shock sensor until reach the proper sensitivity.
c. Test the Optional Sensor 2 (Connected to H6 4 Pin Plug):
Press and release the transmitter
and buttons together three times. Three chirps to indicate you
are in the optional sensor (connected to H6 4 pin plug) test mode.
1. Activate the warn-away (first stage of the optional sensor); system will emit a short chirp.
2. Activate the full alarm (second stage of the optional sensor); system will emit a long chirp.
3. Continue to test the optional sensor until reach the proper sensitivity.
Exit: While in test mode, turns the ignition on or press any button to exit the test mode.
19