User's Manual

-- While the engine is running, the parking light & LED will flash, If don’t, please check tach. wire
connection. (H3/7 White/Red) --
6. Press and hold the valet switch for 2 seconds until a long chirp. The RPM signal is learned.
7. Turns off the ignition switch to stop engine running.
Once you complete step 7, you can adjust and test “Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press the button twice to start the vehicle.
2. If everything goes well:
a. Press the button twice to stop engine running. You have been completed this programming
successfully.
b. Press
button once to exit the program mode and the siren will chirp three long chirps.
3. If the crank time is too short, -- The engine did not successfully run before the starter quit cranking --:
a. Press the button twice on the transmitter to stop engine running.
b. Press button to set proper “Check Level ” to Hi position. Two chirps confirm this setting.
c. Repeat the step1 – 4.
4. If the crank time is too long, -- Engine is successfully running, while the starter is still cranking --:
a. Press the button twice on the transmitter to stop engine running.
b. Press button to set proper “ Check Level ” to Low position. One chirp confirm this setting
c. Repeat the step1 – 4.
ENGINE CHECKING VOLTAGE
Important Note: The voltage “Check Level” for most vehicles would be set in “Hi Check Level”, while in
“Engine Check Voltage” mode, the “Check Level” must be set at “HI” position first.
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
th
push until five chirps with a long chirp is
hearing then release the valet switch.
3. Press
and buttons at the same time twice to set the “Engine Checking Voltage”. Two chirps
confirm this setting.
4. Press
button twice to set “Check Level” to “HI” position. Two chirps confirm this setting.
Once you complete step 4, you can adjust and test “Start Timer” as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
1. Press the button twice on the transmitter to start the vehicle.
2. If everything go well, Wait for 20 seconds:
a. If the engine still running.
I. Press the button twice to stop engine running. You have been completed this programming
successfully.
II. Press
button once to exit the program mode and the siren will chirp three long chirps.
b. If the engine shut down after the vehicle has been started.
I. Press the
button twice to stop engine running.
II. Press
button once to set “Check Level” to “LOW” position. One chirp confirm this setting
III. Repeat the step1 – 2.
3. If the crank time is too long. -- Engine is successfully running, while the starter is still cranking --:
a. Press the button twice to stop engine running.
b. Press
button to set proper “Start Timer”. The chirp will confirm these enter.
-- Decrease “Start Timer” is necessary. --
c. Repeat the step1 – 4.
4. If the crank time is too short. -- The engine did not successfully run before the starter quit cranking --:
a. Press the button twice to stop engine running.
b. Press
button to set proper “Start Timer”. The chirp will confirm these enter.
-- Increase “Start Timer ” is necessary.--
c. Repeat the step1 – 4.
ENGINE CHECKING OFF
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
th
push until five chirps with a long chirp is
hearing then release the valet switch.
3. Press
and buttons together three times to set the “Engine Checking Off”. Three chirps confirm
this setting.
Once you complete step 3, you can adjust and test “Start Timer” as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
1. Press the button twice on the transmitter to start the vehicle.
2. If everything goes well:
18