User's Manual
Table Of Contents
- Door Lock
- Door Unlock
- Your vehicle doors are unlocked and the system is Disarmed
- Armed Mode
- Hidden Alarm Mode
- Activate the car jacking mode
- Valet Mode
- Remote Transmission
- You are transmitting the signal to control unit
- In – Range Indicator
- Hood Trigger
- Trunk Trigger
- Door Open Warning
- Sensor Trigger
- Engine Cranking
- Engine Running
- Timer Control Start
- Engine start automatically at the same time next day or every 2 / 3-hour.
- Indoor temperature of your vehicle
- Activate Channel 4
- Activate Channel 6
- You have set morning call alarm
Diesel Engine with
Wait-To-Start Light
(H3/9 White/Green
wire must be
connected)
10 seconds warn-up
timer for Diesel
Engine
15 seconds warn-up
timer for Diesel
Engine
20 seconds warn-up
timer for Diesel
Engine
Five Chirps/
30 seconds warn-up
timer for Diesel
Engine
Six Chirps/
45 seconds warn-up
timer for Diesel
Engine
2 10 minutes run time 20 minutes run time 30 minutes run time 5 minutes run time
3
Factory alarm
disarm with channel
3 on
Without this feature
4
Flashing parking
light output
Constant parking
light output
5
Door lock before
start
Door lock after
shut-down
Door lock before
start and Door lock
after shut-down
Without this feature
6
+
3 Hour Time start 2 Hour Time Start 1 Hour Time Start
7
+
Temperature-Contro
l Start OFF
Temperature-Contro
l Start 5F (-15C)
Temperature-Contro
l Start – 4F (-20C)
Temperature-Contro
l Start – 22F(-30C)
8
+
Fahrenheit display
for temperature
Celsius display for
temperature
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will
chirp three long chirps.
START FEATURE “II” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
th
push until five chirps with a long chirp is
hearing then release the valet switch. You are now in the Start feature ‘II’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
Exit the programming mode.
2
+
Engine Checking
Voltage
Engine Checking
TACH..
Engine Checking
OFF
RPM learning
3
Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10
chirps),
4
Hi check level Low check level
5
-
Start or Stop the system for TESTING & ADJUSTMENT
6
+
Test Mode for
Trigger input
Test Mode for
Sensor 1 / Shock
Sensor (Zone 4).
Test Mode for
Optional Sensor 2
(Zone 6)
Exit: Press the button to exit the program mode and the siren will chirp three long chirps.
ENGINE CHECKING TACH. / RPM LEARNING
Important Note: You must program the “Tach Signal” before trying to remote start.
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
th
push until five chirps with a long chirp is
hearing then release the valet switch.
3. Press
and buttons at the same time once to set the “Engine Checking TACH.” One chirp
confirms this setting.
4. Press the
button once, one chirp to indicate the system in features “RPM Learning mode”.
5. Start the vehicle with the key.
17