User's Manual

Note: Maximum is 19 hours.
4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30
1. Press & hold the
button for 3 seconds, with two-melody sound and the “Hours” digit flashes for
adjusting.
2. Press & hold the
button for 2 seconds, the LCD screen will flash / icon and “Hours”
digit for Hour set-up.
3. Press the
or button to decrease or increase the hour digit until AM 6:00
4. Press the button once again then the minute digit flashes.
5. Press the
or button to decrease or increase the minutes digit until AM 6:30
6. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.
A. PROGRAMMING THE REMOTE TRANSMITTER:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the
valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating
the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds to exit the program mode and the siren will
chirp three long chirps.
B. FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times and holding in on 2
nd
push until one chirp with a long chirp is hearing then
release the valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a. The siren chirps and LED pause will indicate previously setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps.
b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
1
All Siren/Horn
arming, disarming
and tamper
indicator chirps on
Siren/Horn arming
Chirps OFF
w/second TX button
push confirmation,
Disarm chirp OFF. All
tamper indicator
chirps ON
All Siren/Horn
arming, disarming
and tamper
indicator chirps off
Siren/Horn arming
and disarming
chirps off with all
tamper indicator
chirps on
2
Active arming Passive arming
without passive door
locking
Passive arming
with passive door
locking.
3
Automatic Rearm
off
Automatic Rearm on
4
Instantly Door Ajar
Warning
45 seconds delay
Door Ajar Warning.
5
+
Without Car-jack
mode
Active Car-jack mode Passive Car-jack
mode
6
+
Panic with Ignition
off
Panic with Ignition on
& off
Panic with Ignition
on & off. Panic
with No time limit.
Without Panic
function.
14