MODEL X11RF-LCD REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5.
TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ……………………………………….………………….……………………….. 4 B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ..…………………………….…………………..…... 4 C. LED DISPLAY .……………..……………………………………………………………………….…………………….……. 4 D. CHIRP INDICATOR ..………..……………………………………………………………………………..…………………... 4 E. PARKING LIGHT …….……..…………………………………………………………………………..………………………. 4 F. ACTIVE ARMING – ARM & LOCK .………………………………………………………………………………………..….
OPERATION: A. REMOTE TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock Doors & Arm System Arm and Bypass The Sensor 1 (Zone 4). Press twice within 3 seconds Arm and Bypass The Sensor 2 (Zone 6). Press within 5 seconds Arm and Bypass The Sensor 1 and 2 Press within 5 seconds Arm System and Hidden Alarm Function Press within 3 seconds Car Locator Upon armed (3-second) Panic function Press and Hold for 3 seconds. + + Silent Arming / Disarming Ignition in "off" position.
F. ACTIVE ARMING – LOCK & ARM: 1. Press button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system. System Arm Hood Ajar Trunk Ajar Door Ajar Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter .
System Disarm Sensor 1 Trigger Hood Trigger Sensor 2 Trigger Trunk Trigger Doors Trigger Ignition Trigger CLEAR THE FLASH ICON: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transceiver. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times.
M. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impact will trigger the warn-away signal. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking lights, and dome light will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING: Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed O. SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only) Press the transceiver button first, within 3 seconds press (C) button. It responds with one melody sound and all trigger’s records will immediately displayed on the LCD screen. Note: If it has no responds then you are out of range. P.
V. POWER ON MEMONRY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected. REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: 1. Press button twice on the transmitter. 2. The parking light will activate to indicate the remote start received the signal. (A melody sounding from your Remote LCD transceiver and “ ” icon will flashes on the LCD screen to confirm the remote start was activated.) 3.
feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. If the system is set up to start in temperature mode, the system can be programmed to automatically start the vehicle engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air temperature every 3 (2 /1) hour and will only start the engine during extreme cold temperatures.
LCD REMOTE CONTROL TRANSCEIVER: Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. A. BATTERY REPLACEMENT: A 1.5V type AAA Lithium / digital camera use / Alkaline battery powers the Remote Transmitter. When the icon shall be displayed on the LCD screen.
Activate Channel 7 C7 Time Monitor Alert Alarm You have set morning call alarm Power Save Mode Save the battery power Count Down Timer Reminder when time is up for parking Melody Mode Remote Control alert user through melody sound Button Lock Disable the transmission function temporarily Vibration Mode Remote Control vibrates when the system is triggered Driver paging / Lose and Found Someone is paging you in front of your vehicle C.
It is useful when you are in a noisy place and difficult to hear beep sound from the remote control as the remote control in this mode, vibrates itself if your security system is triggered. button first, within 3 seconds press and hold the button to select the Press the mode of melody ( ) / vibration ( ) or melody with vibration ( ) , the / icon will displayed on the LCD screen. 7.
first, within 3 seconds press and hold and buttons at the same time 1. Press for 2 seconds with one long beeping sound and the “ ” timer icon will display on the LCD screen to indicate the system is back to first transceiver pin code. 2. While the “ ” timer icon display on the LCD screen, you can remote control and communicate with a first vehicle security system. It has one short “bi” sound while pressing the button of the LCD screen transceiver. D.
Note: Maximum is 19 hours. 4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30 button for 3 seconds, with two-melody sound and the “Hours” digit flashes for 1. Press & hold the adjusting. button for 2 seconds, the LCD screen will flash / icon and “Hours” 2. Press & hold the digit for Hour set-up. or button to decrease or increase the hour digit until AM 6:00 3. Press the 4. Press the button once again then the minute digit flashes. or button to decrease or increase the minutes digit until AM 6:30 5.
7 + 8 + Standard Horn output Function Standard horn pulse Five Chirps / LED five pulses S-M-L-S-M-L Horn output for alarm trigger, panic and car- finder only “SOS” type S-S-S - L-L-L - S-S-S Six Chirps / LED six pulses S-S - L - S-S S-L-S-L S-S-S - L Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds to exit the program mode and the siren will chirp three long chirps. ALARM FEATURE “II” PRORAMMING: 1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
1 2 3 4 5 + 6 + 7 + + 8 *9 + H1/6 Pink Wire = Ignition 2 off during Crank H11/5 Brown Wire = 5-second pulse Siren output H3/9 White / Blue Wire = 2 pulse activate H4/4 White / Yellow Wire Disarm Signal Output = Same as Door Unlock Output H3/13 Yellow Wire = Ignition 3 off during Crank H3/17 Black / Green Wire Channel 4 Output = Latched output until IGN ON FIVE Chirps= Output for 30 sec.
2 3 4 5 7 + + 8 + 6 Diesel Engine with Wait-To-Start Light (H3/9 White/Green wire must be connected) 10 seconds warn-up timer for Diesel Engine Five Chirps/ 30 seconds warn-up timer for Diesel Engine 10 minutes run time Factory alarm disarm with channel 3 on Flashing parking light output Door lock before start Six Chirps/ 45 seconds warn-up timer for Diesel Engine 20 minutes run time Without this feature 3 Hour Time start 2 Hour Time Start Temperature-Contro l Start OFF Fahrenheit display for t
-- While the engine is running, the parking light & LED will flash, If don’t, please check tach. wire connection. (H3/7 White/Red) -6. Press and hold the valet switch for 2 seconds until a long chirp. The RPM signal is learned. 7. Turns off the ignition switch to stop engine running. Once you complete step 7, you can adjust and test “Check Level” as below: CHECK LEVEL PROGRAMMING: (TEST and ADJUST) 1. Press the button twice to start the vehicle. 2. If everything goes well: a.
button twice to stop engine running. You have been completed this programming a. Press the successfully. b. Press button once to exit the program mode and the siren will chirp three long chirps. 3. If the crank time is too long. -- (Engine is successfully running, while the starter is still cranking --: a. Press the button twice to stop engine running. button to set proper “Start Timer”. The chirp will confirm these enter. b. Press the -- Decrease “Start Timer” is necessary -c.Repeat the step1 – 4. 4.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
