MODEL SRT-9000 REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL 1
OLED REMOTE TRANSCEIVER A. OLED DISPLAY…………………………………………………………………………………………………………………… Reset the Remote Transceiver B. CHARGE THE BATTERY ……….…………………………………………………………………………….……..…….. C. MAIN PAGE ……………………………………………………………………………………………………….…………… D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION ……………………………………….…………. E. SELECT THE TRANSCEIVER FEATURES …………………………………………..……………….……………….
REMOTE START OPERATION A. TO REMOTE START THE VEHICLE ………..………………………………………..………………………..…………..18 B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START ……………..……………………..….....18 C. TEMPORARY STOP FEATURE ……………………………………………….……………………….…………………… 18 D. TURBO TIMER MODE ……………………..………………………………….……………….……………...………..….… 18 E. TIMER START …………………………………………….…………….………………………………..…………………..19 3 (2 or 1) Hours Timer Start Daily Timer Start Cancel the Timer Start F. TEMPERATURE CHECK ……………….……………………………………………..…….…...
REMOTE TRANSCEIVER (TX) A.
Power by built-in 3.7V lithium polymer battery, if the OLED screen is flash, charge your remote display low battery or transceiver. While the battery of the Remote Transceiver is under the battery charging, you can push the ” ” button to check charging condition. Optional AC Power Supply If you have optional AC POWER SUPPLY / AC ADAPTOR (Output Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge the battery indoors.
While the flash icon Push the button, the count down timer will display. Press the button 2 to set off the count down time or While the icon flash Push the or button, the OLED screen will display individually i.e. daily start timer, timer start or temperature start, depend on which you selected. While the Push the button, the alert alarm time will display. icon flash Press the button 2 to set off the alert alarm timer D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION: 1.
Spin down the Spin down the switch Spin down the switch switch to the page 3 to the page 2 Spin down the switch to the page 4 to the page 1 Spin down the switch to the page 5 Spin down the switch Spin down the switch resume to main page. to the page 6 E- P1- 1. “BUTTON BEEP” SETTING: Example: Set the “Button Beep Disable”.
E- P1- 4. “DEMO MODE”: Spin down the switch Demo movie playing Press the button 4 to start Demo movie to the page 1 Press the any Button to exit. E- P2- 1. “POWER SAVE” SETTING: Example set the “Power Save Enable”. While the power save mode, the LCD remote transceiver uses “0” current to save the battery power. Spin down the switch to the page 2 Press the button 1 to change the setting. Press the button 1 and it will display previously setting. Press the button and the setting is done.
Press the button 1 and the “-” flashes for setting. Spin down the switch to set the “0”. Press the button 3 and the setting is done. D- P2- 4. “LIGHTING FOR OLED” TIMER SETTING: Example: set the LCD display from 3 seconds to9 seconds. Spin down the switch to the page 2 Press the button 4 and it will display previously setting D- P3- 1.
or Press the button 2 to set the ”minute” digit to “30”. Press the button 3 to set the alert alarm timer and the icon will flash on the main page. Push the button Press the button 2 to set off the alert alarm timer or press any button to stop alarm while alert alarm timer trigger While the icon is flashing or When alert alarm timer trigger, the screen will display alert alarm timer C- P3- 3.
D- P4- 1. “NAME OF TX ” SETTING: Spin down the switch to the page 4 Press the button 1 and the “-” flashes for setting. Example Set Name of Transceiver 1 to MIKE Press the button1 and the “-” flashes for setting. Spin down the switch to set the “M”. Press the button 1 and the “-” flashes for setting. Spin up the ” switch to set the ”I”. Spin down the Press the button 1 and the “-” flashes for setting. Spin up the switch to set the ”E”. Press the button 3 and the setting is done.
Spin down the switch Press the button 1 & 2 at same time to set the defaults. Press the button 4. to the page 6 OPERATION A.
C. CHIRP INDICATORS: Chirp 1 chirp 2 chirps 3 chirps 4 chirps 6 chirps Function Arm Disarm Ajar Warning Disarm / Triggered Car Locator D. PARKING LIGHT: Parking light 1 flash 2 flashes 3 flashes 12 flashes Constant On Function Arm Disarm Disarm / Triggered Car Locator Under Remote Start E. ACTIVE ARMING – LOCK & ARM: 1. Press button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed.
G. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press button on the transmitter. 2. The siren will chirp twice and parking light flash twice to indicating that the security system is now disarmed. The vehicle’s door will unlock and dome light turns on for 30 seconds upon disarming when interfaced with the security system.
I. VALET MODE: (System in Disarm or Valet mode) The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times or ten times for warn-away triggers. Each time, the same sensor (zone 4 or zone 6) is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm. After the fifth trigger (tenth for warn-away), “Noise Abatement Circuit” ignores, or bypasses that sensor until the other sensor or switch is trigger.
Q. DOME LIGHT CONVENIENCE DELAY & SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following: 1. Upon disarming, the interior light will remain on for 30 seconds. 2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turn on the ignition switch or arm the alarm will turn off the dome light. R. IGNITION CONTROL DOOR LOCK/UNLOCK. (See Alarm Feature II – 2 Programming).
Spin up the switch Press the button 3 and the setting is To the page 6 done also the “TX 3” will display on the OLED screen V. POWER ON MEMONRY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected. REMOTE START OPERATION A. TO REMOTE START THE VEHICLE: 1. Press button twice on the transmitter. 2. The parking light will activate to indicate the remote start received the signal.
Your system has the ability to automatically start the vehicle every 1,2 or 3 hours, run for the pre-programmed time (5, 10, 20 or 30 minutes), and then shut off. This will continue for 48 hours. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine.
TEST MODE In this test mode, this system can test the all of the trigger input. The installer can save time to test the sensitivity of the 2-stage shock sensor and optional sensor and without using the traditional arming/disarming procedures to test the sensors. 1. Press the button to disarm the system, within 10 seconds 2. Spin up the switch to 3. Select 1 / 2 the page 5 4. Press button 2 to test the Two Stage Shock Sensor: Two chirps to indicate your are in the two-stage shock sensor test mode. 1.
