User's Manual

ManualsBrandsAdvance Security ManualsAutomotiveCar Alarm Transceiver

REMOTE ENGINE STARTER

WITH ALARM SYSTEM

OWNER’S MANUAL

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must

practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10. Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place.

OPERATION

A. REMOTE TRANSMITTER OPERATION:

Transmitter Button System Function Remark

Lock Doors & Arm System

- Arm and Delete The 2 Stage Shock Sensor. Press twice within 3 seconds

- Arm System and Hidden Alarm Function Press within 3 seconds

Car Locator Upon armed

(3-second) Panic function Press and Hold for 3 seconds.

+ Silent Arming / Disarming Ignition in "off" position.

+ (2-second) Active Anti Car-Jacking Mode Ignition in "on" position press and

hold for 2 seconds

Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm System Press twice within 3 seconds.

(2-second) Trunk Release (Channel 3) Press and Hold for 2 seconds

- Passive Arming By-pass While the system Disarmed.

Activate or Turn Off The Remote Start Press twice within 3 seconds.

+ Turbo Time Mode

+ Channel # 4 Timer Output

B. LED display:

LED Function LED Function

Off Disarmed 2 flashes... pause Zone 2 / Trigger on Trunk/Hood

Slow Flash Armed 3 flashes... pause Zone 3 / Trigger on Door Switch

Fast Flash Passive Arming 4 flashes... pause Zone 4 / Trigger on Shock Sensor

On (Solid) Valet Mode 5 flashes... pause Zone 5 / Trigger on Ignition Switch

C. CHIRP INDICATORS: D. PARKING LIGHT:

Chirp Function Parking light Function

1 chirp Arm 1 flash Arm

2 chirps Disarm 2 flashes Disarm

3 chirps Ajar Warning 3 flashes Disarm / Triggered

4 chirps Disarm / Triggered 12 flashes Car Locator

6 chirps Car Locator Constant On Under Remote Start

Summary of content (9 pages)

PAGE 1
REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5.
PAGE 2
E. ALARM OPERATING CONDITION: 1. Arming 2. Disarming 3. Trigger 4. Panic 5. Car-Jacking 6. Car Locator Siren / Horn 1 or 3 Chirps 2 or 4 Chirps Alarming Alarming Alarming 6 Chirps Parking Light LED Doors Starter Dome Light 1 Flash Slow Flash Locking Disable 2 or 3 Flashes Unlocking Turns on for 30 -second Flashes Slow Flash Disable Flashes Flashes Flashes Flashes Disable Flashes 12 Flashes Locking F. ACTIVE ARMING – LOCK & ARM: 1. Press button on the transmitter. 2.
PAGE 3
System Disarm Ignition Trigger Doors Trigger Trunk/Hood Trigger Shock Sensor Trigger TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. PATHWAY ILLUMINATION (See Alarm Feature “II - 4” Programming): This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
PAGE 4
or button on the transmitter again for 3 1. To stop the alarm, press and hold the transmitter or button is pressed and released, the panic seconds. Also if any transmitter buttons other than mode will be turned off immediately. 2. If the button is not pressed, the alarm will automatically stop after 30 seconds. M. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impact will trigger the warn-away signal. 2.
PAGE 5
O. DOME LIGHT CONVENIENCE DELAY & SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following: 1. Upon disarming, the interior light will remain on for 30 seconds. 2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turn on the ignition switch or arm the alarm will turn off the dome light. P. IGNITION CONTROL DOOR LOCK/UNLOCK. (See Alarm Feature II – 2 Programming).
PAGE 6
1. The hood is opened. 2. The brake pedal is pressed. 3. Move the optional remote start enable toggle switch to OFF position. (If installed) 4. The gear selector is in any gear other then “PARK” or “NEUTRAL” SAFE START (Child safety mode) (See Start Feature I – 5 Programming.) button twice on the transmitter to start the vehicle.
PAGE 7
button twice to remote start the vehicle. As soon as the vehicle is running and the parking 1. Press the light have turned on or flashing. 2. Immediately depress the button then press and hold the button for 2 seconds. The parking light will flash (4) times. The siren or horn chirps (4) times. The vehicle is no longer programmed to start automatically. G. TO TURN OFF THE REMOTE START: When the engine is running (by remote start), if you want to stop it, 1.
PAGE 8
Remote Transmission You are transmitting the signal to control unit Trunk/Hood Trigger Trunk or Hood is illegally opened (Zone 2) Shock Sensor Trigger Trigger on Shock Sensor (Zone 4) In – Range Indicator Your are within the remote control range. Door Open Warning Doors are illegally opened (Zone 3) Warn Away trigger Trigger on Shock Sensor (Zone 1) Low Battery You have to replace the battery of remote control.
PAGE 9
and buttons at the same time until one long beep is heard. 1. Press and hold Programming has now been entered. 2. Within 5 seconds press and hold button until one beeping sound is heard. 3. To exit programming mode, take no action for five seconds. The remote control will generate two long beeps to indicate programming mode has been exited. 2.