User's Manual

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the
valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating
the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times and holding in on 2
nd
push until one chirp with a long chirp is hearing then
release the valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
a. The siren chirps and LED pause will indicate newly setting.
b. The system would advance to [2] LED flash, [2] chirp. (The factory default settings is always [1] LED
flash, [1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
All chirps on Siren chirp on only Horn chirp on only All chirps off
2
Active arming Passive arming
without passive door
locking
Passive arming with
passive door
locking.
3
Automatic Rearm on Automatic Rearm off
4
Instantly Door Ajar
Warning
45 seconds delay
Door Ajar Warning.
5
+
Without Car-jack mode Active Car-jack mode Passive Car-jack
mode
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
3 / 45 seconds Delay Door Ajar Warning:
This feature controls the error chirp that is generated if the system is armed with the door trigger active.
This useful in a vehicle that has a long dome light delays after the door has been closed. If the system is
armed before the dome light has turned off, the security system will generate the door trigger error chirp.
Use this feature to disable the door open error chirp.
ALARM FEATURE “II” PRORAMMING:
1 . Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 . Push the Valet switch 4 times and holding in on the 4
th
push until two chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 . Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp / LED
one pulse
Factory Default
Setting
Two Chirps / LED
two pulse
Three Chirps / LED
three pulse
Four Chirps / LED
four pulse
1
0.8-second Door
lock pulses.
3.5-second Door
lock pulse.
Double pulse unlock Door lock with
“Comfort Feature”
2
Ignition controlled
door locks &
unlocks
Ignition controlled
door locks only
Ignition controlled
door unlocks only
Without ignition
controlled door locks
& unlocks
3
Door lock before
start
Door lock after
shut-down
Door lock before
start and Door lock
after shut-down
Without this feature
10