User's Manual
Table Of Contents
- BLACK 4-PIN CONNECTOR. – TWO-WAY TRANSCEIVER/ANTE
- The Two-way transceiver/antenna mounts on the location above the belt line (dashboard) of the vehicle for best reception. We suggest you mount it on the lower left or upper left-hand side of windshield.
- - Remove the protective tape backing.
- - Carefully align the two-way transceiver/antenna and apply to windshield.
- METHOD 1
- METHOD 2
MAY/18/2005
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
5 WIRE ALTERNATING DOOR LOCKS
+12V
Cut the Existing
Lock Wire
Green / White
Blue / Red
Green / Red
Cut Existing Unlock
X
Blue / White
Cut the Unlock Wire
Lock
Unlock
OEM Door Master Lock
OEM Slave
Door Lock
Switch
+12V
LockUnlock
To All Other
Door Lock
Motors
LT. Green /
Black Wire
x
X
OEM
Door Lock
Motor
Blue / Yellow
Green / Yellow
+ 12V
+ 12V
85
86
87
87A
30
6-Pin
Door
Lock
Wire
Harness
VACUUM OPERATED DOOR LOCKING SYSTEM:
TYPICAL OF MERCEDES BENZ AND AUDI.
Locate the wire under the driver's kick panel. Use the
voltmeter connecting to ground, verify that you have th
e
correct wire with the doors unlocked, the voltmeter will
receive "12 volts". Lock the doors and the voltmeter wi
read "0 volt". Move the alligator clip to +12V and the
voltmeter will receive "12 volts". Cut this wire and mak
e
connections. Be sure to program door lock timer to
3.5 seconds. (See Feuture I – 2 Programming.)
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
GROUND SWITCHED DOOR LOCKS
Cut Existin
g
Unlock
X
LockUnloc
k
OEM Door Master Lock Switch
To All Other
Door Lock
Motor
LT. Green / Black
Wire
OEM
Door Lock
Motor
Blue / White
Green / White
Green / Yellow
Existing
Lock Wire
Existing
Unlock Wire
6-Pin
Door
Lock
Wire
Harness
Blue / Red
Blue / Yellow
+12V
OEM Door
Lock Relay
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
POSITIVE SWITCHED DOOR LOCKS
Cut Existing Unlock
X
LockUnlock
OEM Door Master Lock
To All Other
Door Lock
Motors
LT. Green /
Black Wire
OEM Driver's
Door Lock
Motor
+ 12V
Blue / Red
Existing Pos.
Lock Wire
Existing Pos.
Unlock Wire
30
87A
87
86 85
+12V
Blue / White
Green / White
Green / Yellow
Blue / Yellow
+ 12V
OEM Door
Lock Relay
6-Pin
Door
Lock
Wire
Harness
A. PROGRAMMING TRANSMITTER:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Program switch 3 times and holding in on 3rd push until a long chirp is hearing and the LED
start to flash then release the Program switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the horn responds with a confirming chirp / a flash from
parking light / the LED turns on for 2 seconds indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
B. FEATURES PROGRAMMING:
DELUXE 200-LCD
9