User's Manual
Table Of Contents
- BLACK 4-PIN CONNECTOR. – TWO-WAY TRANSCEIVER/ANTE
- The Two-way transceiver/antenna mounts on the location above the belt line (dashboard) of the vehicle for best reception. We suggest you mount it on the lower left or upper left-hand side of windshield.
- - Remove the protective tape backing.
- - Carefully align the two-way transceiver/antenna and apply to windshield.
- METHOD 1
- METHOD 2
MAY/18/2005
a. Press the button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
b. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
3. If the crank time is too short, (Engine not running, while stops cranks):
a. Press the
button on the transmitter to stop engine running.
Press button on the transmitter to set proper “Check Level ” to Hi position. [2] LED flashes,
[2] chirps to confirm this setting
b. Repeat the step1 – 4.
4. If the crank time is too long, (Engine already successfully running, while still cranks):
a. Press the
button on the transmitter to stop engine running.
Press button on the transmitter to set proper “ Check Level ” to Low position. [1] LED flash,
[1] chirp to confirm this setting
b. Repeat the step1 – 4.
c.
ENGINE CHECKING VOLTAGE
Important Note: The “Check Level” for most vehicles would be set in “Hi Check Level”, while in “Engine
Check Voltage mode”, the “Check Level” must be set at “HI” position first.
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Program switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is
hearing and the LED start to flash then release the Program switch.
3. Press the transmitter
and buttons at the same time to set the “Engine Checking Voltage”. [1] LED
flashes, [1] chirps to confirm this setting
Once you complete step 3, you can adjust and test “Start Timer” as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
1. Press the button twice on the transmitter to start the vehicle.
2. If everything goes well: Wait for 15 seconds:
a. If the engine still running.
I. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
II. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
b. If the engine shut down after the vehicle has been started.
I. Press the
button twice on the transmitter to stop engine running.
II. Press
button on the transmitter to set “Check Level” to LOW position. [1] LED flash,
[1] chirp to confirm this setting
III. Repeat the step1 – 2.
3. If the crank time is too long, (Engine already successfully running, while still cranks):
a. Press the
button twice on the transmitter to stop engine running.
b. Press
button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm this
enters. (Decrease “Start Timer” is necessary.)
c. Repeat the step1 – 4.
4. If the crank time is too short, (Engine not running, while stops cranks):
a. Press the
button twice on the transmitter to stop engine running.
b. Press
button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm this
enters. (Increase “Start Timer ” is necessary.)
c. Repeat the step1 – 4.
d.
RETURN TO FACTORY DEFAULT SETTING
1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position.
2. Push the Program switch 12 times and holding in on the 12
th
push until six chirp with a long chirp is
hearing and the LED start to flash then release the Program switch. You are now in the “Return To Factory
Default Setting” programming mode.
3. Press and hold the
and buttons at the same time on the transmitter for 5 seconds, there will be a
confirmation six chirp with 3 long chirp and the LED turns On for 2 seconds to confirm the system Feature
Programming all returns to factory default setting.
DELUXE 200-LCD
12