User's Manual
Table Of Contents
- BLACK 4-PIN CONNECTOR. – TWO-WAY TRANSCEIVER/ANTE
- The Two-way transceiver/antenna mounts on the location above the belt line (dashboard) of the vehicle for best reception. We suggest you mount it on the lower left or upper left-hand side of windshield.
- - Remove the protective tape backing.
- - Carefully align the two-way transceiver/antenna and apply to windshield.
- METHOD 1
- METHOD 2
MAY/18/2005
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
Gasoline Engine Diesel Engine and
10 seconds warn-up
timer
Diesel Engine and
15 seconds warn-up
timer
Diesel Engine and
20 seconds warn-up
timer
2
20 minutes run time 30 minutes run time 5 minutes run time 10 minutes run time
3
Factory alarm
disarm with channel
3 on
Without this feature
4
3 Hour Time start 2 Hour Time Start
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
FEATURE “IV” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Program switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is
hearing and the LED start to flash then release the Program switch. You are now in the Start feature ‘IV’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
Exit the programming mode. (3 long chirp & 3 parking light flashes to confirm this exit.)
2
+
Engine Checking
Voltage.
Engine Checking
TACH. /
RPM Learning Mode
3
Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4 chirps),
1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-second (7 chirps),
2.0-second (8 chirps), 3.0-second (9 chirps), 4.0-second (10 chirps),
4
Low check level for
“Engine checking
Tach.”
Hi check level for
“Engine checking
Voltage.”
Hi check level for
“Engine checking
Tach.”
Low check level for
“Engine checking
Voltage.”
Exit: Press the button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
ENGINE CHECKING TACH. / RPM LEARNING
IMPORTANT NOTE: You must program the “Tach Signal” before trying to remote start.
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Program switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is
hearing and the LED start to flash then release the Program switch.
3. Press and release the transmitter
and buttons at the same time twice [2] LED flash, [2] chirp to
confirm the system in features “RPM Learning mode”.
4. Within 10 seconds, start the vehicle with the key. (While the engine is running, the parking & LED will
flash, If don’t, please check VIOLET/WHITE wire connection.
5. Press and hold the Program switch for 2 seconds until a long chirp and the LED / the parking light will
constantly on for two seconds. The RPM signal is learned.
6. Turns off the ignition switch to stop engine running.
Once you complete step 6, you can adjust and test “Check Level” as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well:
DELUXE 200-LCD
11