User's Manual

MAY/18/2005
FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Program switch 2 times and holding in on 2
nd
push until one chirp with a long chirp is hearing
and the LED start to flash then release the Program switch. You are now in the feature ‘I’ programming
mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a. The horn chirps and LED pause will indicate previously setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the transmitter
button ‘A’ again until the module advances to your desired setting.
a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps.
b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
1
Chirps on Chirps off
2
0.8-second Door
lock pulses.
3.5-second Door lock
pulse.
Double pulse
unlock
Door lock with
“Comfort Feature”
3
Ignition controlled
door locks &
unlocks
Ignition controlled
door locks only
Ignition controlled
door unlocks only
Without ignition
controlled door
locks & unlocks
4
Without this feature Door lock before start Door lock after
shut-down
Door lock before
start and Door lock
after shut-down
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
FEATURE “II” PRORAMMING:
1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Program switch 4 times and holding in on the 4
th
push until two chirps with a long chirp is
hearing and the LED start to flash then release the Program switch. You are now in the feature ‘II’
programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp / LED one pulse
Factory Default Setting
Two Chirps / LED two
pulses
Three Chirps / LED three
pulses
1
Pathway illumination feature
“off”
Parking light turns “on” for
30- second upon an unlock
signal
Parking light turns “on” for
30- second upon an unlock
signal & 10-second upon a
lock signal.
2
Constant parking light
output
Flashing parking light output
3
Brown/Black Wire = Factory
Security Rearm Signal
Output
Brown/ Black Wire =
Ground Output During Start
(Crank)
4
LT. Green / Black Wire =
Dual Pulse door unlock
output
LT. Green / Black Wire =
Factory Security Disarm
Signal Output
LT. Green / Black Wire =
Start Status Output
(Shock Sensor Bypass)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
FEATURE “III” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Program switch 6 times and holding in on the 6
th
push until three chirps with a long chirp is
hearing and the LED start to flash then release the Program switch. You are now in the feature ‘III’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
DELUXE 200-LCD 10