User's Manual

Two-way remote transmitter operation
E7s
Transmitter
Button
System Function Remark
Lock Doors
Panic
Press & hold for 3 sec.
Unlock Doors
Trunk Release (Channel 3) Press and Hold for 2 seconds
Activate The Remote Start Push once
Stop remote start operation **
Push Twice
+
Switching code For 2nd Car
Operation.
PRESS BTN ON
Transmitter
Action
LED ON Transmit
( RED )
LED ON
Receive ( Green )
Transmitter
sound
SIREN (CAR)
CHIRP
+
LOCK
1 SHORT
FLASH
LED ON 1 SEC. 1 1
UNLOCK
1 SHORT
FLASH
LED ON 1 SEC. 2 2
START
ON
1 SHORT
FLASH
FLASH 2 TIMES
4 SHORT
CHIRPS
N/A
+
START
OFF
1 SHORT
FLASH
FLASH 3 TIMES 3 LONG CHIRPS N/A
(PRESS & HOLD)
TRUNK
1 SHORT
FLASH
N/A N/A N/A
The LED on the two way remote will flash every 3 seconds while the vehicle is running
QUICK START
USERS
GUIDE
If you do not understand any part of this quick start users
manual and would like the complete version, Please visit
our web site @ www.encoreautomotivesystems.com
E
ncore
E
-
5
Encore E
-
7
s
Remote
Transmitter
REMOTE TRANSMITTER OPERATION:
One Way Remote
CHIRP INDICATORS:
PARKING LIGHT:
Chirp Function Parking light Function
1 chirp Lock 1 flash Lock
2 chirps Unlock 2 flashes Unlock
ON Running on remote start
LED if installed
LED Function
Off Unlock
Slow Flash Locked
On (Solid) Valet Mode
PROGRAMMING TRANSMITTERS:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter
memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 4 TIMES and stay in ON position.
“Within 15 seconds”.
2. Push the Valet switch 4 times and hold it on the 4th push until a long chirp is heard then release
the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp,
indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes
will confirm exit.
For Customer service, Please call (855) Go-Encore
855-463-6267, 8:00-5:00 PST
WARNINGS:
As with any product that performs automatic functions, there are certain safety precautions
that you must practice and be aware of.
• Keep the transmitter out of children’s reach.
• Do not leave anyone in the vehicle while running on remote control.
• Alert servicing personnel that the vehicle can be started automatically.
• Do not start the vehicle by remote while it’s in an enclosed area or garage.
• Always apply the parking brake and lock the vehicle as you exit the vehicle.
• The vehicle windows must be rolled up.
• Should the unit malfunction, disconnect the fuse until the problem is corrected.
• The use and operations of this system is the sole responsibility of the operator.
• Some areas may have local ordinances that prohibit leaving a vehicle running on public
streets.
•
THIS DEVISE CANNOT BE USED ON ANY STANDARD TRANSMISSION VEHICLE.
FOR AUTOMATIC TRANSMISSIONS ONLY!
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
ACTIVE LOCK:
1. Press button or + on the two way transmitter.
2. The horn, if installed will chirp once and parking lights will flash once
indicating that the system is now active. The vehicle doors will lock upon
activating when interfaced with the keyless entry system.
ACTIVE UNLOCK:
1. Press button on the transmitter.
2. The horn will chirp twice and parking light will flash twice to indicating that
the keyless system is now unlocked. The vehicle doors will unlock.
DEACTIVATING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to ‘ON’ position.
2. Within 10 seconds push and release the antenna mounted valet switch
VALET MODE:
The valet switch allows you to temporarily by-pass all system function,
eliminating the need to hand your transmitter to parking attendants or garage
mechanics. When the system is in valet mode, and remote start functions are
bypassed, Enter Valet Mode:
1. Under Unlock condition, turn the ignition to “ON” position.
2. Press and hold the antenna mounted valet switch for 2 seconds until the
LED turns on. The LED will remain on as long as the system is in ‘valet
mode’.
Exit Valet Mode:
1. Return to normal operation, turn ignition ‘on’.
2. Press and hold valet switch for 2 seconds, The LED will turn off
Indicating that the system has exited the valet mode.
IGNITION CONTROL DOOR LOCKS.
If the vehicle’s door locks have been interfaced to the security system, the
system will automatically lock the vehicle’s doors when the ignition is turned
“ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.
TRUNK RELEASE (Additional Installation Required)
Press and hold the
or button on the two way transmitter for 3 seconds to
activate the trunk release or other electric devices.
PANIC FUNCTION: One way remote ONLY
The transmitter can be used as a remote panic switch to manually trigger the system
in case of emergency.
1. Press and hold the button for 3 second. The unit will immediately sound.
2. During panic mode, the normal function of this transmitter button will be disabled.
The transmitter and buttons can be used to lock and unlock the door (if the
option is installed).
3. To stop the alarm, press and hold the transmitter button on the transmitter again for
3 seconds.
.
4. If the button is not pressed, the system will stop after 30 seconds.
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL
INSTALLATION ONLY
Encore Two way
E1S (Two way)