PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits.
PRO PLM SYSTEM LAYOUT TRACKING PORT 8 Pin GROUND IGNITION DOOR TRIGGER (+) +12 VOLT BATTERY PARKING LIGHT OUTPUT DOOR TRIGGER (-) PARKING LIGHT INPUT ARMED OUTPUT (-) 6 Pin OPEN DK GREEN BLACK/WHITE LT.
SETUP & PROGRAMMING - CONSUMER MODE Consumer Mode Transmitter Programming Bank 1. 2. 3. 4. 5. 6. 7. Turn the ignition ON. Press and release the override button 3 times. The system will chirp 1 time. Press the lock button of each transmitter you wish to program. The system will respond with 1 chirp for each accepted transmitter. Turn the ignition OFF to exit transmitter programming. The system will chirp 2 times to confirm exit.
SETUP & PROGRAMMING - CONSUMER MODE, CONTINUED Dome Light Delay/Theater Lighting Programming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming. 1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK.
SETUP & PROGRAMMING - LOT MODE Lot Mode Transmitter Programming Bank - ACM Transmitter 1. 2. 3. 4. 5. 6. 7. Turn the ignition ON. Press and release the override button 3 times. The system will chirp 1 time. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button. The system will respond with 1 chirp. Turn the ignition OFF to exit transmitter programming. The system will chirp 2 times to confirm exit.
SETUP & PROGRAMMING - LOT MODE Dome Light Delay/Theater Lighting Programming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming. 1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK.
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER Transitioning into Lot Mode - ACM Transmitter 1. 2. 3. 4. 5. 6. 7. Turn the ignition ON. Press and release the override button 3 times. The system will chirp 1 time. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button. The system will respond with 1 chirp. Turn the ignition OFF to exit transmitter programming. The system will chirp 2 times to confirm exit.
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER, CONTINUED Transitioning into Factory Keyless Upgrade Mode - BLUE 1. 2. 3. 4. 5. 6. 7. Open a vehicle door. Enter the vehicle number into an ACM keypad. Press the UNLOCK button. Press and release the # button. Press and release the “BLUE” button. The LED will flash blue 1 time and the system will chirp 3 times. Close the vehicle’s door. Note: The ACM keypad must be authorized for transitioning.
TRANSITIONING BETWEEN MODES - SHORT RANGE TRANSMITTER Transitioning into Lot Mode 1. 2. 3. 4. 5. 6. 7. Turn the ignition ON. Press and release the override button 3 times. The system will chirp 1 time. Press button 1 of the short range transmitter. The system will respond with 1 chirp. Turn the ignition OFF to exit transmitter programming. The system will chirp 2 times to confirm exit. Note: This system has 1 button programming which programs all channels of the transmitter to the system at once.
1. 8 PIN MAIN HARNESS BLACK - Chassis Ground Source (-) Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended grounding point is a metal surface in the driver’s side kick panel area. Note: Do not ground the BLACK wire with any other vehicle components. YELLOW - 12 Volts Ignition Input (+) Locate the vehicle’s ignition wire at the ignition switch.
1. 8 PIN MAIN HARNESS, CONTINUED BROWN - Negative Door Input (-) Locate the vehicle’s dome light or door pin switch wire. Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This wire will register positive voltage when the door is closed and the interior light is off. Connect the BROWN wire to the vehicle’s negative door input wire(s). NOTE: Certain vehicles may require multiple connections.
2. 6 PIN HARNESS, CONTINUED DK BLUE - Trunk Release Output (-) This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories such as trunk release. To Activate press and hold UNLOCK for 2 seconds. Locate the vehicle’s trunk release wire at the trunk release switch. Verification: This wire will register either positive voltage or ground when the trunk release is activated. 3.
4. 3 PIN DOOR LOCK HARNESS RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output Negative Switching and Negative Switching with 2-step unlock feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register ground when the lock and unlock switches are activated. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
4. 3 PIN DOOR LOCK HARNESS, CONTINUED RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output Positive Switching and Positive Switching with 2-step unlock feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register positive voltage when the lock and unlock switches are activated. Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
4. 3 PIN DOOR LOCK HARNESS, CONTINUED RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output One Wire Negative Multiplexed and One Wire Negative Multiplexed with 2-step Unlock Feature: All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable ground when the switch is activated. Please consult the Vehicle Wire Color and Location Chart for specific resistor values for the vehicle.
4. 3 PIN DOOR LOCK HARNESS, CONTINUED RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output One Wire Positive Multiplexed and One Wire Multiplexed With 2-step Unlock Feature All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable positive voltage when the switch is activated. Please consult the Vehicle Wire Color and Location Chart for specific resistor values for your vehicle.
4. 3 PIN DOOR LOCK HARNESS, CONTINUED RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output Reverse Polarity (5-Wire Door locks) and Reverse Polarity with 2-step Unlock All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will rest at ground and register positive voltage when the lock and unlock switches are activated.
4. 3 PIN DOOR LOCK HARNESS, CONTINUED RED - Lock Output (-) GREEN - Unlock Output (-) RED/BLACK - 2nd Door Unlock Output Adding Door Actuators After installing door actuators, (not supplied). Connect the RED and GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
5. ACCESSORY CONNECTORS 6 Pin Override Push-Button and LED The status LED / override button should be mounted in a visible and easily accessible location on the driver’s dashboard area. Route the harness and plug the 6 pin connector into the module. 4 Pin Tracking Port: (Off White Connector) This 4 pin port is used for connecting the PROPT20 PursuiTrak GPS system.
6. SYSTEM POWER-UP PROCEDURE 1. After all connections are complete, turn the vehicle's ignition key to the ON position. 2. Insert the 5 Amp fuse into the respective fuseholder. 3. Turn the ignition key to the OFF position. 7. System Testing 1. Follow each instruction below. 2. Verify that the system operates as indicated under each instruction. Refer to the system owners manual. 3. Check the appropriate wire connections and/or fuses if the unit fails to perform a specific function.
8. SYSTEM TESTING, CONTINUED Press DISARM: 1. Doors unlock. 2. Factory alarm (if equipped) is turned off. 3. Siren/horn sounds once/ parking lights flash once. 4. Courtesy lights turn on for 30 seconds, or until ARM is pressed or ignition is turned on. 5. Vehicle starter is enabled. Press DISARM twice: Passenger doors unlock if using 2-stage unlock. Press CAR FIND/PANIC: Siren/horn sounds 5 times.
ITS FUNCTIONALITY ITS Introduction The PRO PLM may be used as a ITS (Interior Theft Sensor) and when doing so it is designed to honk the horn if a light impact is detected or trigger the vehicle's factory alarm if a harder impact is detected. Note: The vehicle MUST have a factory alarm that is triggered by opening the vehicle's door. Option #10 must be changed in the feature programming bank for the system to function as the ITS.
ITS LAYOUT TRACKING PORT 8 Pin GROUND IGNITION DOOR TRIGGER (+) +12 VOLT BATTERY N/A DOOR TRIGGER (-) N/A N/A 6 Pin OPEN DK GREEN BLACK/WHITE LT.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
