User's Manual

MAY/24/2005
560A 12
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
ALARM FEATURE “II” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 4 times and holding in on the 4
th
push until two chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp / LED one
pulse
Factory Default
Setting
Two Chirps / LED
two pulse
Three Chirps / LED
three pulse
Four Chirps / LED
four pulse
1
0.8-second Door
lock pulses.
3.5-second Door
lock pulse.
Double pulse unlock Door lock with
“Comfort Feature”
2
Ignition controlled
door locks & unlocks
Ignition controlled
door locks only
Ignition controlled
door unlocks only
Without ignition
controlled door locks
& unlocks
3
Door lock before
start
Door lock after
shut-down
Door lock before
start and Door lock
after shut-down
Without this feature
4
Pathway illumination
feature “off”
Parking light “on”
for 30- second upon
an unlock signal
Parking light “on” for
30- second upon an
unlock signal &
10-second upon a
lock signal.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Comfort Feature:
Some Vehicles have a special “COMFORT feature”. When you lock the door with the key, you just have to
keep on turning the key on the door about 5 or 7 seconds and the window will close directly.
If your vehicle with “COMFORT feature” and you wish the door being locked and the window being closed
automatically at the same time by remote control, you can set the alarm feature
II-1
“with comfort feature”.
ALARM FEATURE “III” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and holding in on the 6
th
push until three chirps with a long chirp is
hearing then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1
H2/4 Brown Wire =
Siren Output
H2/4 Brown Wire =
Horn Output
2
H5/3 White Wire =
Dome light Output
H5/3 White Wire =
Horn Output
H5/3 White Wire =
Factory Security
Rearm Signal Output
H5/3 White Wire =
Ground Output
During Start (Crank)
3
H5/4 Pink Wire =
2-Step Door
Unlock Output
H5/4 Pink Wire =
Factory Security
Disarm Signal Output
H5/4 Pink Wire =
Start Status (Shock
Sensor By-Pass
Control) Output
4
Without Shock
sensor Test Mode
With Shock Sensor
Test Mode
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Ground Output During Start (Crank) = This wire will provide a 200 mA ground output while the starter
output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire
found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.
TEST AND ADJUST THE SHOCK SENSOR: