User's Manual

APRIL /29/2004
400S 美 8
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulses
1
Exit the programming mode. (3 long chirp to confirm this exit.)
2
Override Without Password Pin Code
/
Press
& hold button for 4 seconds to delete the
Password pin code
Override With Password Pin Code
/
Password pin code programming
3
“ TEST” Mode for Zone 2 Hood & Zone 3 Door
Pin Switch
“ TEST” Mode for Zone 4 / the Optional
Sensor connected to 4 pin plug.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
Password Pin Code Setup:
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ IV’ programming mode.
3. Press and release the transmitter button once, [2] LED flash, [2] siren/horn chirp to indicate you are in
features “ Password Pin Code Programming mode” .
4. Within 15 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet Switch
from 1 – 9 times.
5. Within 15 seconds of the last entered 10ths digit, turn the Ignition switch to “ ON” position.
6. Within 15 seconds, enter your chosen second 10ths digit by pressing and releasing the valet Switch from
1 – 9 times.
7. Finish by turning the ignition switch to “ OFF” position.
If the new password code was accepted, the unit would report back the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause and then the second digit code. The unit
will report the new code three times with a one-second pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ ON” for more then 5 seconds during
of above steps, the unit will revert back to the last successfully stored code. A [3] long chirps to confirm exit.
Will revert back to the last successfully stored code
Delete Password Pin Code (Override Without Password Pin Code):
(Factory default setting)
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is hearing
then release the valet switch.
3. Within 15 seconds, press and hold the transmitter button for 4 seconds. One long chirp to confirm
Deleted the Password Pin Code.
Example: To program the Password Code 92, you would;
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ IV’ programming mode.
3. Press and release the transmitter button once, [2] LED flash, [2] siren/horn chirp to indicate you are in
features “ Password pin code programming mode” .
4. Within 15 seconds, press and release the valet switch 9 times.
5. Within 15 seconds of the last entered 10ths digit, turn the Ignition Switch to “ ON” position.
6. Within 15 seconds press and release the valet switch 2 times.
7. Turn the Ignition Switch to “ OFF’ position.
You will note the LED flashing nine times, pause and then flash two times, pause. This pattern will be
repeated three times indicating the new code (92) has been accepted and stored in memory.
Test Mode
In this test mode, this system can test the Zone 1 Warn Away Trigger / Zone 2 Instant ground trigger / Zone
3 Door trigger and the Zone 4 optional sensor sensitivity. The installer can save time to test the optional
sensor sensitivity and sensor without using the traditional arming/disarming procedures to test the sensors.
Enter:
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ IV’ programming mode.