User's Manual

APRIL /29/2004
400S 美 7
2. Push the Valet switch 6 times and holding in on the 6
th
push until three chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ III’ programming mode.
3. Press and release the transmitter button ‘ A’ corresponding to the feature ‘ A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
The Vehicle has aftermarket Turbo timer installed: The system Can be
Arm with the engine running and
1
The Vehicle without
Turbo (The system
Can not be Arm with
the engine running)
The shock sensor will
be bypass as long as
the engine running.
The shock sensor will
be bypass for one
minute
The shock sensor will
be bypass for three
minutes
2
H1/4 Brown Wire =
Constant Siren output
for 6-tone siren
H1/4 Brown Wire =
5-second pulse Siren
output for signal tone
siren
H1/4 Brown Wire =
Random pulse Siren
output
H1/4 Brown Wire =
Pulse Output
3
H7/7 Red / White
Wire Channel 3 =
1 second pulse
output for trunk
release.
H7/7 Red / White
Wire Channel 3 =
Latch output
H7/7 Red / White
Wire Channel 3 =
Timer controlled
output
4
+
H7/10 Purple / Black
Wire Channel 4 =
Momentary output
H7/10 Purple / Black
Wire Channel 4 =
Latched output
H7/10 Purple / Black
Wire Channel 4 =
Latched output and
reset with ignition
“ on”
H7/10 Purple / Black
Wire Channel 4 =
Timer programming
(set to any interval
between 1 second
and 2 minutes.)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
Channel 3 (4) Timer Control Output Programming
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and holding in on the 6
th
push until three chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ III” programming mode.
3-a. Press and release the transmitter button 2 times, [3] LED flash, [3] siren/horn chirp to indicate
you are in features “ Channel 3 Timer Programming mode” .
3-b. Press and release the transmitter and buttons at the same time three times, [4] LED flash,
[4] siren/horn chirp to indicate you are in features “ Channel 4 Timer Programming mode” .
4. Press and hold the valet switch, the timer will immediately start.
5. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation.
(Set to any interval between 1 second and 2 minutes)
Note 1: If your built-in timer controls window/sunroof closure in your car DO NOT change the timer setting!
This requires installer-only programming. Changing the value will adversely effect operation and may
cause damage.
Note 2:
Momentary output = The momentary output selection will output a negative signal from the Channel 4
output immediately when the channel 4 button is pressed and will continue until the button is release.
Latched output = The latched output selection will output a negative signal as soon as the Channel 3 (4)
button is pressed and will continue until the button is pressed again.
Latched output / reset with ignition = The latched / reset with ignition output selection operates just like
the latched output but will reset or stop when the ignition is turned on.
ALARM FEATURE “IV” PRORAMMING:
1. Turn the Ignition 'switch ‘ ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 8 times and holding in on the 8
th
push until four chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘ IV’ programming mode.
3. Press and release the transmitter button ‘ A’ corresponding to the feature ‘ A’ you want to program.