PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 1 R Vehicle Security OWNER’S MANUAL Model: PLUS-4800 For Technical Assistance, please call (800) 638-3600, or visit www.magnadyne.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 2 Congratulations on your purchase of a quality Carbine automotive security system. Carbine automotive security products have been designed to provide the consumer with a product that is technologically superior and will provide years of trouble free operation. The information enclosed will provide a ready reference of the operation and maintenance of your new security system.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 3 Automatic Arming (without using the transmitter) (Continued) A. The horn/siren will chirp one time. B. The LED indicator will begin to flash slower. C. The parking lights will flash one time. D. All protected entrances are armed. Note 1: Re-opening a protected entrance before the system becomes armed will stop the arming timer. After closing the entrance the timer will begin counting again from zero.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 4 Override Switch Operation (Continued) Override Operation: (Security System is Armed) 1. Enter the vehicle (the security system will begin sounding at this point). 2. Place the ignition key into the ignition switch and turn the switch to the “On” position. 3. Within 5 seconds of turning the ignition key “On”, place the override switch to the “On” position. 4. The horn/siren will stop sounding. 5. The LED indicator will be solid red.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 5 User Discretion Silent Arming: Your security system can be instructed to become armed or disarmed without the horn/siren chirps by the transmitter. To operate this feature at any time, simply press the LOCK and UNLOCK buttons at the same time to arm or disarm your security system without the chirp indications.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 6 Upgrade Options: Option #1: Remote Power Door Lock/Unlock Control Note: Your vehicle must have an electronic door locking system for this feature to operate. Installing Option #1 will allow the transmitter to lock and unlock your vehicle’s doors as it arms and disarms your security system. Option #2: Remote Trunk/Hatch Release (Channel #2) Installing Option #2 will allow the transmitter to open your vehicles trunk or rear hatch.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 7 Programmable Features: The following is a brief description of the operation of each programmable feature. Any adjustment to the operation of these features must be performed by the dealer who installed your Carbine Security System. These features are not user adjustable.
PLUS-4800-UM.qxp 2/7/05 2:43 PM Page 8 System Maintenance: The only maintenance that your Carbine security system requires is a periodic check that it’s functions are operating properly. The battery supplied with regular transmitter (A) will last about 1 year and the battery supplied with passive transmitter (B) will last about 6 months. Heavier usage will shorten battery life. Reduced transmitter range is usually a sign that the transmitter battery is becoming weak and should be replaced.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 1 R Vehicle Security INSTALLATION MANUAL Model: PLUS-4800 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 2 Table of Contents Step 1: Component Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Step 2: 10-Pin Main Harness Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Step 3: 5-Pin Power Harness Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Step 4: Optional Accessory Connections . . . . . . . . . . . . . . .
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 3 Step 1: Component Installation (Continued) Installing the Alarm Status LED: Find a suitable location for the LED and drill a 5/16" hole in the desired location. Feed the 2-pin plug through the hole and press the body of the LED into place. Run the LED wires to the location of the alarm control module. Step 2: 10-Pin Main Harness Installation The main wire harness contains 8 wires which all have a specific purpose.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 4 Step 2: 10-Pin Main Harness Installation (Continued) Brown Wire: (Siren + Output) Connect the brown wire to the positive wire from the siren. Ground the remaining wire from the siren for proper operation. Blue Wire: (Optional Grounding Sensor Input) The blue wire is an instant grounding trigger input for optional hood/trunk grounded pin switches or any electronic sensor.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 5 Step 3: 5-Pin Power Harness Installation The power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed for each wire. Power Harness First Socket Second Socket First Vacant Socket: The first vacant wire socket is a low current (300mA) grounded output wire that can be used to activate the vehicle’s interior lighting system when the security system is disarmed.
PLUS-4800-IM.
PLUS-4800-IM.
PLUS-4800-IM.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 9 Step 4: Optional Accessory Connections (Continued) Starter Disable Wiring Using a Common Relay Using the wiring information and diagram below, connect the optional starter disable relay as follows: A. Locate the “Start Only Wire” coming from the ignition key switch and cut it. B. Connect the ends of the cut start wire to pins #30 and 87a of the relay pack. C. Connect the single gray wire harness supplied (with 2-pin black connector) to pin #85 on the relay. D.
PLUS-4800-IM.
PLUS-4800-IM.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 12 Step 5: Transmitter Programming Step 1 Step 2 Override Switch ON ON OFF OFF Switch in “Off” Position Plug In the Power Harness Step 3 Make Sure the Override Switch is in the Off Position Step 4 3x ON Turn On Ignition Flip the Override Switch On then Off 3 Times The siren will chirp 1 time. You are now in the transmitter code programming mode. The LED will be a solid red.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 13 Step 5: Transmitter Programming (Continued) Step 5 Regular Transmitter Passive Transmitter (Optional) Lock Lock Unlock Panic Aux Unlock Panic Passive Unlocking Aux Push Lock Button The LED will begin flashing slowly and the horn/ siren will emit 1 short chirp. The code has now been learned. The transmitters supplied are pre-programmed to the receiver module. You should use the following instructions when adding a new or replacement transmitter.
PLUS-4800-IM.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 15 Step 7: General Testing To test the basic functions of the alarm system repeat the following procedures: 1. Turn off the ignition key and exit the vehicle closing all protected entrances. 2. Press the LOCK button on the transmitter. You will hear a siren/horn chirp, the parking lights will flash one time and the LED status indicator will flash at normal speed. 3. Wait 5 seconds, then open a protected entrance. The siren/horn will begin to sound.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 16 Step 8: Speciality Feature and Optional Equipment Testing (Continued) Exit Valet Mode 1. Turn the ignition key to the “Off” position and open any door. 2. Press and hold down the UNLOCK + buttons. 3. The door locks will lock and unlock. Release the buttons. 4. The LED will be off indicating that the system is out of Valet Mode. * Override Operation: (Security System is Armed) 1. Enter the vehicle and the security systems will begin sounding at this point. 2.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 17 Step 8: Speciality Feature and Optional Equipment Testing (Continued) LED Status Indicator Operation: LED is off = Alarm is disarmed. LED is flashing = Alarm is armed. LED is flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood/ trunk or electronic sensor. LED flashing in a 3 flash hold sequence = Tamper warning, alarm was triggered by an open door. LED is on steady = Alarm is in the valet mode (Ignition key is “On”).
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 18 Step 8: Speciality Feature and Optional Equipment Testing Ignition Controlled Door Locking: (Door lock activation must be installed) When programmed on in “Remote Feature Programming”, ignition controlled locking is active 3 seconds after the ignition key is set the On position, the door locks will automatically become locked. When the ignition key is turned to the Off position, the door locks will unlock.
PLUS-4800-IM.
PLUS-4800-IM.qxp 2/7/05 2:40 PM Page 20 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. 1)•This device may not cause harmful interference, and 2)•This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
