User's Manual

8
E. PROGRAMMING PASSWORD:
1. Turn ignition on then within 10 seconds push valet switch for 2 seconds.
2. LED will turns on.
3. Within 4 seconds, turn ignition key 'off-on-off-on-off'. A confirmation long chirp from siren.
4. LED will slow flash from 1 through 10 for 3 cycles. Wait until LED flash to your selected number.
4. As soon as LED turns on your selected number, quickly turn ignition key 'on-off'.
5. A long chirp from siren, the number is programmed.
6. LED will show the programmed number for 2 cycles.
Example: To program password number 5, you would;
1. Turn ignition key on, press valet switch 2 seconds.
2. Turn ignition 'off-on-off-on-off'.
3. Wait until LED flash 5 times, then quickly turn ignition on-off. A long chirp from siren.
4. LED will flash 5 times to indicate your password number is 5.
F. PROGRAMMING VOLTAGE/RPM START OF TIME OR VALUE:
Since different vehicle model has different engine start pattern, some cars require longer crank time to start engine, while
some are not. So this section is for user to adjust their vehicles' engine crank time. Or user can select RPM start value to real
monitor their vehicles' tachometer RPM value.
If user use voltage start pattern to remote start. (PROGRAMMING FEATURES of third stages of No. 1 voltage/RPM
selection). This section goes on adjust voltage start of crank time. If use RPM start pattern, then it goes on adjust RPM start
value.
ENTER:
1. Turn ignition on then off.
2. Press valet switch 3 times, there will be a confirmation chirp.
3. Press button 4 on the transmitter, there will be short chirp(s).
For voltage start (factory preset on 4 chirps of 2 seconds)
1 short chirp is 0.5 second crank time, 2 chirps is 1.0 seconds, 3 chirps is 1.5 seconds, 4 chirps is 2.0 seconds, 5 chirps is
2.5 seconds and 6 chirps is 3.0 seconds.
For RPM start (factory preset on 2 chirps of 90% value)
1 short chirp is 70% value of RPM, 2 chirps is 90% value of RPM and 3 chirps is 100% value of RPM.
4. Use valet switch to program your desired time or value.
5. Push one time of valet switch that will add up one time of the chirp(s).
6. For example the system use voltage start, and upon entering, (press button 4) siren chirp 4 times. You want to adjust the
crank time to 3.0 seconds. Then you need to push the valet switch 2 times. The siren will chirp 6 times. If you would like to
change to 1.5 seconds, after 6 chirps, press switch 3 times again. Siren will chirp 3 times. The programming method is
cycling.
EXIT:
Turn ignition on, or press button 1 on transmitter. There will be 3 long chirps for confirmation.
DIAGNOSTIC PARKING LIGHT
The system has a built-in diagnostic routine which indicate why the unit turned the engine off the last time the unit was used.
The parking light will flash 1 to 4 times to indicate which of the following caused the engine off.
1. 1 flash ----- RPM fail. (Check up the 6-pin starter plug wires of No. 6 green wire connection.)
2. 2 flashes----Voltage fail. (The vehicle’s battery power is below 11 volts)
3. 3 flashes----Hood fail. ( Hood is opened, or check up the wiring of the blue wire coming from the main harness)
4. 4 flashes----Hand brake fail. ( Hand brake is released, before remote start, check up the hand brake must pull up, and
the 6-pin starter plug wires of No. 2 violet wire connection
OPERATION:
A. TRANSMITTER OPERATION: (4 buttons transmitter)
For designated channel setting:
Transmitter Button System Function Remark
Button 1 Arm/disarm & door lock/unlock