User's Manual

7
Enter: Turn the ignition 'on' then 'off'. Within 15 seconds push the valet switch 6 times. (A long chirp.) And push & hold the
valet switch for over 2 seconds, with 1 long chirp confirmation.
By using first stage programming features method to program second stage's features.
4. Third stage programming features:
Enter: Turn the ignition 'on' then 'off'. Within 15 seconds push the valet switch 6 times. (A long chirp.) And push & hold the
valet switch for over 2 seconds, with 1 long chirp confirmation. Again push & hold the valet switch for over 2 seconds, with 1
long chirp confirmation.
By using first stage programming features method to program second stage's features.
5. Exit:
During programming, if you don’t respond to previous step in 15 seconds, or any time press transmitter’s button 1, it will exit
features programming, which indicates by 3 long chirps.
FIRST STAGE:
Push valet
switch times:
Chirp, parking
light flash times
Turn ignition from
'OFF' to 'ON'
Turn ignition from
'ON' to 'OFF'
Show 1 short chirp 2 short chirps
Select Feature " ON " Feature " OFF "
1 1 Current sensor ON Current sensor OFF
2 2 Chirp ON Chirp OFF
3 3 Active arming Passive arming
4 4 Rearm ON Rearm OFF
*5 5 Voltage sensor 3 sec.arming delay. Voltage sensor 30 sec.arming delay.
6 6 Car-Jacking OFF Car-Jacking ON
7 7 Password OFF Password ON
SECOND STAGE:
Push valet
switch times:
Chirp parking
light flash times
Turn ignition from
'OFF' to 'ON'
Turn ignition from
'ON' to 'OFF'
Show One short chirp Two short chirps
Select Feature " ON " Feature " OFF "
1 1 Lock/unlock 0.8 sec. Lock/unlock 3.5 sec.
*2 2 2-pulse unlock OFF. 2-pulse unlock ON.
3 3 Passive door lock ON Passive door lock OFF.
4 4 Ignition on door lock ON Ignition on door lock OFF
5 5 Ignition off door unlock ON Ignition off door unlock OFF
6 6 Disarm parking light OFF. Disarm parking light on 30"
THIRD STAGE:
Push valet
switch times:
Chirp parking
light flash times
Turn ignition from
'OFF' to 'ON'
Turn ignition from
'ON' to 'OFF'
Show One short chirp Two short chirps
Select Feature " ON " Feature " OFF "
*1 1 Voltage start. RPM start.
2 2 Running time 10 min. Running time 20 min.
3 3 Before start door lock OFF Before start door lock ON
4 4 Ignition off door lock OFF Ignition off door lock ON
5 5 Ignition 2 ON during crank Ignition 2 OFF during crank
6 6 Gasoline Diesel
NOTE:
For system programming features all returns to presetting "ON", turn the ignition 'on' then 'off'. Within 15 seconds push the
valet switch 3 times. (A long chirp.) Then press button 1 and 2 together for 5 seconds, there will be a confirmation long chirp.
*Voltage sensor 3/30 seconds arming delay.
Set 3 sec.: Upon close the door, vehicle's interior light will not light up.
Set 30 sec.: Upon close the door, vehicle's interior light will light up.
* 2- pulse unlock off / on:
Set off: For most regular vehicles that require only single pulse to unlock doors.
Set on: For some vehicles that require two pulses to unlock the doors.
* Voltage / RPM start:
Determines how the system will monitor engine speed.
Select voltage start: The system uses voltage level automatically monitoring engine speed. That is by monitor AC voltage
from the negative side of the coil.
Select RPM start: The system will detect the engine’s tachometer signal as the start selection.