User's Manual

6
In program 1
st
transmitter the LED will with one flash…pause sequence.
Press button 1 to program channel 1, 1 short chirp and LED on to confirm programmed and ready program channel 2.
Press button 2 to program channel 2, 2 short chirps and LED on to confirm programmed and ready program channel 3.
Press button 3 to program channel 3, 3 short chirps and LED on to confirm programmed and ready program channel 4.
Press button 4 to program channel 4, 4 short chirps and LED on to confirm programmed
Program 2
nd
transmitter, push valet switch one time, the LED will with two flashes…pause sequence.
Press button 1 to program channel 1, 1 short chirp and LED on to confirm programmed and ready program channel 2.
Press button 2 to program channel 2, 2 short chirps and LED on to confirm programmed and ready program channel 3.
Press button 3 to program channel 3, 3 short chirps and LED on to confirm programmed and ready program channel 4.
Press button 4 to program channel 4, 4 short chirps and LED on to confirm programmed
Program 3
rd
transmitter, push valet switch one time again, the LED will with three flashes…pause sequence.
Use above steps to program each channel.
Program 4
th
transmitter, push valet switch one time again, the LED will with four flashes…pause sequence.
Use above steps to program each channel.
3. In auto channel:
In program 1
st
transmitter the LED will with one flash…pause sequence.
Press any button on 1
st
TX, 1 short chirp confirm programmed and ready program 2
nd
TX
The LED will with two flashes…pause sequence.
Press any button on 2
nd
TX. 1 short chirp confirm programmed and ready program 3
rd
TX.
The LED will with three flashes…pause sequence.
Apply the same procedure to program 3
rd
and 4
th
, after the 4
th
transmitter programmed the system will auto exit.
4. Exit:
Turn ignition to 'off' position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
Note: If more than 4 transmitters programmed, the system only kept the last 4 transmitters.
B. PROGRAMMING OPTIONAL SENSOR (PIR OR DOOR/WINDOW SENSOR)
This system has a very unique interfacing with optional sensor, to extend more protection, such as PIR (IR-73) sensor or
Door/Window sensor. (DS-70)
For example, in your garage you can put a PIR for protection. (A device to detect person's movement in a protected area.) If
system armed, a person walk through the detect area, the siren inside the car will alarming to raise the attention to the owner.
So the same thing applies in door/window sensor, (A device to detect door/window open.) you may put the sensor to the
garage door or window. If system armed, a person opens the door or window, the siren will alarm.
Maximum program 4 different sensor codes.
The programming procedure is the same as above A. PROGRAMMING TRANSMITTER of auto channel, The difference is
only upon enter you push the valet switch 9 times. (1 long chirp to confirm enters).
During programming, you will need to activate the sensor to let the system program it's code.
C. PROGRAMMING (RPM) TACHOMETER:
(Must connect 6-pin starter connection plug of green tachometer wire to vehicle's tachometer, and select RPM start
on the programming features.)
ENTER:
Turn ignition switch ‘on’, and start the engine, with engine running.
Push valet switch 3 times, there will be 1 long chirp, and LED fast flashing confirm enter.
Again press the valet switch 2 seconds, there will be a short chirp and LED solid on for a while confirm enter.
EXIT:
Turn the ignition switch 'off'. Or leave it for 15 seconds, system will auto-exit.
D. PROGRAMMING FEATURES:
There are 3 stages of totally 19 programming features to select. (Factory preset all features to "ON" position)
1. Enter:
Turn the ignition 'on' then 'off'. Within 15 seconds push the valet switch 6 times. (A long chirp.) It is on first stage
programming features.
2. First stage programming features:
Push the valet switch times that equal the feature number you want. Example: Push valet switch 2 times, it's on chirp on/off
selection. The siren will chirp 2 times, LED flash 2 times to confirm enter this feature.
Select chirp on, turn ignition from 'off' to ‘on’. 1 chirp for confirmation.
Select chirp off, turn ignition from 'on' to ‘off’. 2 chirps for confirmation.
If you want to program car jacking when the system is on chirp on/off, push valet switch 4 times again. (Siren chirp 6 times,
LED flash 6 times) The system will add on the previous valet switch pushing.
Note: Totally push valet switch 7 times, the siren chirp 7 times, and LED with 7 flashes… pause sequence. If push the valet
switch again, system will return to feature 1. (Siren chirp 1 time, and LED with 1 flash…pause sequence. It's cycling.)
3. Second stage programming features: