MODEL 6978 REMOTE ENGINE STARTER WITH ALARM SYSTEM MANUAL This system works on only auto transmission vehicle. A. 9 pin wire connection plug B. 6 pin starter connection plug Antenna Wire C. 3 pin door lock plug D. 4 pin optional sensor plug 2 pin LED plug 2 pin valet plug E. 4 pin wire harness F. 4 pin starter connector WIRING: A.
B. 6 pin starter connection plug: Gray: Negative safety input - hood or trunk Violet: Negative safety input - hand brake Yellow: Ignition 2 (-) output Orange: Pulsed ground output during start Blue: OEM alarm output Green: Tachometer connection 1. Gray wire – Negative safety input - hood or trunk. Prevents engine from starting while vehicle is being serviced (or anytime that hood is raised). a.
.Yellow wire:- Ignition 2 ( - ) output -This wire provides a 200mA (-) output in conjunction with the orange (+) 12V ignition output. The yellow wire is designed to disarm a factory installed security system. Some factory systems must be disarmed to allow remote starting. In most cases, the yellow wire may be connected directly to the factory alarm disarm wire. The correct wire will show nagative ground when the key is used to unlock the doors or trunk.
GM. : White, at coil or at HEI distributor. With some three-coil V6 motors, violet/white. Ford: Tan/yellow or yellow/blue, at coil, at diagnostic connector, or at electronic distributor. Toyota/Lexus: (-) G terminal of gray diagnostic connector under hood. Honda/Acura: Blue, in two-pin connector forward of distributor. Mercedes-Benz: Black, at coil under rubber boot. C.
F. 4 pin starter connector Remember that the system does to start a vehicle is duplicate the functions of the ignition key switch! Below, we will explain the three basic functions of the ignition switch. Since this installation will require analysis of the ignition switch functions, we recommend making the three connections below at the ignition switch harness directly.
st In program 1 transmitter the LED will with one flash…pause sequence. Press button 1 to program channel 1, 1 short chirp and LED on to confirm programmed and ready program channel 2. Press button 2 to program channel 2, 2 short chirps and LED on to confirm programmed and ready program channel 3. Press button 3 to program channel 3, 3 short chirps and LED on to confirm programmed and ready program channel 4.
Enter: Turn the ignition 'on' then 'off'. Within 15 seconds push the valet switch 6 times. (A long chirp.) And push & hold the valet switch for over 2 seconds, with 1 long chirp confirmation. By using first stage programming features method to program second stage's features. 4. Third stage programming features: Enter: Turn the ignition 'on' then 'off'. Within 15 seconds push the valet switch 6 times. (A long chirp.) And push & hold the valet switch for over 2 seconds, with 1 long chirp confirmation.
E. PROGRAMMING PASSWORD: 1. Turn ignition on then within 10 seconds push valet switch for 2 seconds. 2. LED will turns on. 3. Within 4 seconds, turn ignition key 'off-on-off-on-off'. A confirmation long chirp from siren. 4. LED will slow flash from 1 through 10 for 3 cycles. Wait until LED flash to your selected number. 4. As soon as LED turns on your selected number, quickly turn ignition key 'on-off'. 5. A long chirp from siren, the number is programmed. 6.
Button 1 Button 1 - 1 Button 1 - 1 Button 2 Button 2 - 2 Button 3 Button 4 Button 4 Button 1 + 2 both Button 1 + 2 both 1 sec Panic function Arm and delete optional sensor Disarm and 2 steps door unlock Channel 2 (trunk) control Passive arming by-pass Channel 3 control Car locator Remote start Silent arm/disarm Activate car-jacking Press 3 sec In disarm, press twice. In arm, press twice. Press 2 sec. Press twice.
Use in emergency, like lost or malfunctions of transmitter. Turn ignition on, within 10 seconds push the override/valet switch, the siren will stop and the system disarmed. 2. VALET MODE: Vehicle in for maintenance or valet parking, the system will not arm. a. Turn ignition on then within 10 seconds push and hold override/valet switch for 2 seconds, the LED will turns on indicates the system is in 'valet mode'. b.
Totally after 90 seconds from beginning, siren still alarming and parking light still flashing, and the starter disable will activate to prevent the vehicle from starting. Override the system to turn off car jacking. (Ignition from off to on, and within 10 seconds push valet switch) N. IGNITION CONTROL POWER DOOR LOCK SAFETY SYSTEM. The vehicle's doors will automatically lock after the ignition key turn 'on' (if all doors are closed.
24 hours auto start: This feature is design for a battery charge usage. When the car owner has a long vocation, he can use this feature to auto start the vehicle and charge the battery every day, to prevent a low battery. Below is how to setup. ENTER: 1. System in disarm condition. 2. Turn ignition switch on then off. 3. Within 15 seconds, push valet switch 9 times. 4. There will be a long chirp to confirm enter setup auto start. Program 4 hours or 24 hours: 1.
