802.11n Wireless Adapter 802.
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement. This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Introduction The 802.11n wireless USB Dongle, USB 2.0 compatible, allows you to connect to your wireless networking. It provides more throughput rate on data communication than traditional 802.11g wireless Dongle. With the built advanced wireless configuration utility, it let it more easily for you to surf your wireless LAN. Features and Benefits System - Standard: IEEE 802.11b/g/n. - Host Interface: USB 2.0 standard. - Data rate: 1, 2, 5.5, 11Mbps for 802.11b; 6, 9, 12, 18, 24, 36, 48, 54Mbps for 802.
System Requirements Before installing the Dongle and related software, make sure your system meets the minimum requirements described below. IBM compatible desktop or notebook PC with available USB slot. - CPU level: no restricted. - Memory size: no restricted. - CDROM drive: no restricted. - USB Host: USB 2.0 suggested. USB 1.0/1.1 leads low data communication rate. - Operation system: Microsoft Windows 2000, XP, XP64, or Vista.
Installation - Insert the Product CD into the CD-ROM drive. - Execute “Setup.exe” in the root directory of the CD, it will guide you to install the Driver and Utility. - Insert the wireless Dongle into the USB slot.
Management Load up utility After the installation, one utility will be run and minimized on Windows system tray bar. ：Indicate wireless adapter detected, and connected to one site. ：Indicated wireless adapter not detected, or not connected to one site. You may double click it to bring up the main menu. You may also use mouse right button to launch or to close it. For Windows XP, the utility provides one option to manage the wireless adapter with Windows Zero Configuration.
Definition of each field - SSID: Name of BSS of IBSS network. - BSSID: MAC address of AP or randomly generated of IBSS. - Signal: Receive signal strength of specified network. - Channel: Channel in use. - Encryption: Encryption algorithm used within than BSS or IBSS. Valid value includes WEP, TKIP, AES, and Not Use. - Authentication: Authentication mode used within the network, including Unknown, WPA-PSK, WPA2-PSK, WPA and WPA2.
- Profile Name: User chose name for this profile. - SSID: User can key in the intended SSID name or use pull down menu to select from available APs. - Power Save Mode: Choose from CAM (Constantly Awake Mode) or Power Saving Mode. There is a check box for CAM when AC power. When this is checked, the wireless NIC will stay full power when AC power cord is plug into power outlet. - Network Type: There are two types, infrastructure and 802.11 ad-hoc modes.
set up the authentication security. The function of each session is shown below Authentication & Security When the Encryption feature is enabled, the other setups are same as the WEP setting. - Authentication Type: There are three type of authentication modes supported. They are open, Shared, WPA-PSK and WPA system. - 802.1x Setting: It will display to set when user use radius server to authenticate client certificate for WPA authentication mode.
802.1x Setting 802.1x is a authentication for 『WPA』and 『WPA2』certificate to server. - Authentication type: i. PEAP: Protect Extensible Authentication Protocol. PEAP transport securely authentication data by using tunneling between PEAP clients and an authentication server. PEAP can authenticate wireless LAN clients using only server-side certificates, thus simplifying the implementation and administration of a secure wireless LAN. ii. TLS／Smart Card: Transport Layer Security.
- Session Resumption: user can choose “ Disable ”, “ Reauthentication ”, “ Roaming ”, “ SameSsid ” and “ Always ”. - Identity and Password: Identity and password for server. - Use Client Certicate: Client Certicate for server authentication. - Tunnel Authentication Protocol: Tunnel protocol, List information include “ EAP-MSCHAP ”, “ EAP-MSCHAP v2 ”, “ CAHAP ” and “ MD5 ” Tunnel Identity: Identity for tunnel. Tunnel Password: Password for tunnel. - CA Server: Certificate Authority Server.
Profile Page Profile can book keeping your favorite wireless setting among your home, office, and other public hot spot. You may save multiple profiles, and activate the correct one at your preference. Definition of each field - Profile: Name of profile, preset to PROF* (* indicate 1, 2, 3,). - SSID: AP or Ad-hoc name. - Channel: Channel in use for Ad-Hoc mode. - Authentication: Authentication mode. - Encryption: Security algorithm in use. - Network Type: including infrastructure and Ad-Hoc.
Link Status Page The page displays the detailed information of the current connection. - Status: Current connection status. If no connection, if will show Disconnected. Otherwise, the SSID and BSSID will show here. - Extra Info: Display link status and current channel in use. - Link Speed: Show current transmit rate and receive rate. - Throughout: Display transmits and receive throughput in unit of K bits/sec. - Link Quality: Display connection quality based on signal strength and Tx/Rx packet error rate.
Statistics Page Statistics page displays the detail counter information based on 802.11 MIB counters. This page translates that MIB counters into a format easier for user to understand. Transmit Statistics - Frames Transmitted Successfully: Frames successfully sent. - Frames Transmitted Successfully Without Retry: Frames successfully sent without any retry. - Frames Transmitted Successfully After Retry: Frames successfully sent with one or more reties.
Advance Page 1. - Wireless mode: Select wireless mode. 802.11b only, 802.11 b/g mixed and 802.11b/g/n mixed modes are supported. - 11b/g Protection: ERP protection mode of 802.11g definition. Auto: STA will dynamically change as AP announcement. On: Always send frame with protection. Off: Always send frame without protection. - Tx Rate: Manually force the Transmit using selected rate. Default is auto. - Tx Burst: Proprietary frame burst mode of this utility. - Enable TCP Window Size:.
About Page About page display the utility and driver version information of the wireless adapter.
