User Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- System Alarms
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
FCC-Required Information TRACER 6000 Series Integrated System Manual
6 Copyright © 2005 ADTRAN, Inc. 612806420L1-1E
FCC Output Power Restrictions
The FCC does not require licensing to implement this device. License-free operation in the industrial,
scientific, and medical band is documented in FCC Rules Part 15.247. It is the responsibility of the
individuals designing and implementing the radio system to ensure compliance with any pertinent FCC
Rules and Regulations. This device must be professionally installed.
The FCC specifies the maximum transmitter power used for antennae of a given gain. FCC Rules Part 15,
Subpart 247 allow for a maximum power of 1 watt (30 dBm) into antennae of a gain less than or equal to 6
dBi. At 2.4 GHz (TRACER 6410), the 1-watt maximum transmitter power must be reduced by 1 dB for
every 3 dB of antenna gain over 6 dBi. This rule is shown in Table 5 on page 20. For the 5.8 GHz band
(TRACER 6420), the maximum output power is 1 watt (30 dBm) regardless of the gain of the attached
antenna. Since the TRACER 6420 L1 and L2 maximum transmit power is 100 milliwatts and
250 milliwatts, respectively, there is no reduction in transmitter output power required.
Exposure to Radio Frequency Fields
The TRACER 6410 is designed to operate at 2.4 GHz with 500 mW maximum transmit power, the
TRACER 6420L1 is designed to operate at 5.8 GHz with 100 mW maximum transmit power, and the
TRACER 6420L2 is designed to operate at 5.8 GHz with 250 mW maximum transmit power.
This level of RF energy is below the Maximum Permissible Exposure (MPE) levels specified in FCC OET
65:97-01. The installation of high gain antenna equipment in the system configuration may create the
opportunity for exposure to levels higher than recommended for the general population at a distance less
than 24 feet (7.3 meters) from the center of the antenna. The following precautions must be taken
during installation of this equipment:
• The installed antenna must not be located in a manner that allows exposure of the general population to
the direct beam path of the antenna at a distance less than 24 feet (7.3 meters). Installation on towers,
masts, or rooftops not accessible to the general population is recommended; or
• Mount the antenna in a manner that prevents any personnel from entering the area within 24 feet
(7.3 meters) from the front of the antenna.
• It is recommended that the installer place radio frequency hazard warnings signs on the barrier that
prevents access to the antenna.
• Prior to installing the antenna to the TRACER output, make sure the power is adjusted to the settings
specified in Section 2 of this manual.
• During antenna installation, be sure that power to the TRACER equipment is turned off in order to
prevent the presence of microwave energy on the coaxial connector.
• During installation and alignment of the antenna, do not stand in front of the antenna assembly.
• During installation and alignment of the antenna, do not handle or touch the front of the antenna.
Per Industry Canada RSS210: “The installer of this radio equipment must ensure that the antenna is located
or pointed such that it does not emit RF field in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canada’s website at www.hc-sc.gc.ca/rpb.These simple
precautions must be taken to prevent general population and installation personnel from exposure to RF
energy in excess of specified MPE levels.
Verify the antenna installation meets all regulations specified in the National Electric
Code (NEC) Article 810 with particular attention to clearances from power and lighting
conductors, mounting, grounding, and antenna discharge unit.