User Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- System Alarms
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
TRACER 6000 Series Integrated System Manual Section 3 Engineering Guidelines
612806420L1-1E Copyright © 2005 ADTRAN, Inc. 41
Frequency Plan
Plan A
Channel Plan
1
Tx 2.419 GHz, Rx 2.459 GHz (TRACER 6410)
Tx 5.744 GHz, Rx 5.824 GHz (TRACER 6420)
2
Tx 2.422 GHz, Rx 2.462 GHz (TRACER 6410)
Tx 5.747 GHz, Rx 5.827 GHz (TRACER 6420)
3
Tx 2.425 GHz, Rx 2.465 GHz (TRACER 6410)
Tx 5.751 GHz, Rx 5.831 GHz (TRACER 6420)
Plan B
Channel Plan
1
Tx 2.459 GHz, Rx 2.419 GHz (TRACER 6410)
Tx 5.824 GHz, Rx 5.744 GHz (TRACER 6420)
2
Tx 2.462 GHz, Rx 2.422 GHz (TRACER 6410)
Tx 5.827 GHz, Rx 5.747 GHz (TRACER 6420)
3
Tx 2.465 GHz, Rx 2.425 GHz (TRACER 6410)
Tx 5.831 GHz, Rx 5.751 GHz (TRACER 6420)
Data Encryption
Encryption Type
Symmetric Triple-DES (3DES)
User Interface
Panel Alarm LEDs
Diagnostics RF link diagnostics and error history, transmit and receive packets
history, real-time signal levels
Test Points RSSI and Ground (GND)
Alarms Normally Open (NO) and Normally Closed (NC)
VT100 Terminal Menu-driven user interface, control of the remote end, event history
Telnet Access Menu-driven user interface, control of the remote end, event history
SNMP Standard MIB support (T1/E1 and Ether-like MIBs); Enterprise MIB
support (ADTRAN TRACER)
VT100 Terminal Interface
Data Rate 9600, 19200, 38400, 57600, 115200 bps
Data Bits 8
Parity None
Stop Bits 1
Terminal Emulation VT100
Table 15. At-A-Glance Specifications (Continued)
Hardware Description Specification