User Manual
Table Of Contents
- Table of Contents
- System Description
- Microwave Path Engineering Basics
- Engineering Guidelines
- Network Turnup Procedure
- User Interface Guide
- 1. Navigating the Terminal Menu
- 2. Menu and System Control
- 3. Menu Descriptions
- > System Status
- > Main Menu
- > System Configuration
- > RF Link Configuration
- > RF Link Performance History (Main Screen)
- > RF Link Error History
- > RF Link Max/Min Received Power History
- > RF Link Min/Max Received Signal Quality History
- > Datapath Provisioning
- > 4xE1 Module Configuration/Status/History (Main Screen)
- > E1x Status/Configuration/Loopback
- > E1x Performance History
- > T1 Module Configuration/Status/History (Main Screen)
- > T1x Status/Configuration/Loopback
- > Ethernet Switch Module Configuration/Status/History (Main Screen)
- > Ethernet Switch Configuration
- > Ethernet Switch Status
- > Management/Utilities (Main Screen)
- > Ping Utility
- > Firmware Upgrade Utility
- > RF Link Management Bridge Configuration
- > System Alarms
- Detail Level Procedures
- MIBs
- Troubleshooting Guide
- 1. Overview
- 2. LED Indicators
- PWR LED
- TST LED
- RF DWN LED
- RF LOW LED
- T1 Interface Alarms
- E1 Interface Alarms
- 1. Display the E1(x) Status screen and check the E1(x) Interface Alarm field to identify the active alarm.
- 1. Verify that the E1 cable is connected to the E1 interface on the TRACER 64x0.
- 2. Verify the connections at the opposite end of the E1 cable.
- 3. Verify that the framing mode (framed, multiframed, or unframed) is the same for both the TRACER 64x0 and the E1 equipment.
- 2. Verify the cable connections for the E1 interface are solid.
- 2. Verify the cable connections for the E1 interface are solid.
- System Alarms
- LAN LEDs
- 3. RF Errors
- 4. Step-by-Step Troubleshooting
- 5. Installing/Troubleshooting the TRACER Hardware
Section 7 MIBs TRACER 6000 Series Integrated System Manual
122 Copyright © 2005 ADTRAN, Inc. 612806420L1-1E
adTRACERremoteintervalCSU2Cses Integer RO
adTRACERremoteintervalCSU2Des Integer RO
adTRACERremoteintervalCSU2Dses Integer RO
adTRACERremoteIntervalValidData TruthValue RO
adTRACERremoteCurrent
adTRACERremoteCurrentRFs Integer RO
adTRACERremoteCurrent24hRFs Integer RO
adTRACERremoteCurrentRFCs* Integer RO
adTRACERremoteCurrent24hRFCs* Integer RO
adTRACERremoteCurrentRxLs Integer RO
adTRACERremoteCurrentMaxRxLs Integer RO
adTRACERremoteCurrent24hMaxRxLs Integer RO
adTRACERremoteCurrentMinRxLs Integer RO
adTRACERremoteCurrent24hMinRxLs Integer RO
adTRACERremoteCurrentRxQs Integer RO
adTRACERremoteCurrentMaxRxQs Integer RO
adTRACERremoteCurrent24hMaxRxQs Integer RO
adTRACERremoteCurrentMinRxQs Integer RO
adTRACERremoteCurrent24hMinRxQs Integer RO
adTRACERremoteIntervalTable
AdTRACERremoteIntervalEntry
adTRACERremoteIntervalEntry
adTRACERremoteIntervalIndex Integer RO
adTRACERremoteIntervalNumber Integer RO
adTRACERremoteIntevalRFs Integer RO
adTRACERremoteIntervalRFCs* Integer RO
adTRACERremoteIntervalMaxRxLs Integer RO
adTRACERremoteIntervalMinRxLs Integer RO
adTRACERremoteIntervalMaxRxQs Integer RO
adTRACERremoteIntervalMinRxQs Integer RO
adTRACERremoteIntervalValidData TruthValue RO
adTRACERremoteTotalTable
AdTRACERremoteTotalEntry
adTRACERremoteTotalEntry
adTRACERremoteTotalNumber Integer RO
adTRACERremoteTotalRFs Integer RO
adTRACERremoteTotalRFCs* Integer RO
adTRACERremoteTotalMaxRxLs Integer RO
Table 6. MIB Variables for TRACER6000.mib (Continued)
* Not supported in TRACER 64x0 models. Listed variable only applies to TRACER split systems.